32 41 Pump and Oil Supply
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2014 BMW X6, 2013 BMW X6, 2012 BMW X6, 2011 BMW X6, and 2010 BMW X6. However, it is still accessible from the selected car via links, so may be relevant.
PUMP AND OIL SUPPLY - TIGHTENING TORQUE SPECIFICATIONS
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Oil reservoir to holder | E70, E71, | M6 | 5.3 Nm | |
| 2AZ Belt pulley to vane pump/power steering pump | E70, E71 | M8 8.8 | Replace microencapsulated screws | 21 Nm |
| E70, E71 | M8 10.9 | Replace microencapsulated screws | 24 Nm | |
| 3AZ Vane pump/power steering pump to engine | E70/N62TU/M57T2 | M10 | 38 Nm | |
| E70, E71 | M8 | 21.4 Nm | ||
| E71/ N54 | M10 x 35 | 38 Nm | ||
| E71/ N63 | M10 | 40 Nm | ||
| E71/ M57T2 | M10 | 38 Nm | ||
| E70/N52 | M10, M12 | Observe screwing sequence | ||
| Jointing torque | 20 Nm | |||
| Torque angle | 90 ° | |||
| 4AZ Pressure line for power steering to vane pump/power steering pump | E70/N62TU | 35.6 Nm | ||
| E70/E71/M57T2/N54, E70/N52 | M14 | Replace all sealing rings | 33 Nm | |
| E71/ N63 | M8 | Replace all sealing rings | 28 Nm | |
| 5AZ Pressure line to power steering gear | E70 | M14 | Replace all sealing rings | 33 Nm |
| E71 | M14 | Replace all sealing rings | 30 Nm | |
| 6AZ Return line to power steering gear | E70, E71 | M16 | Replace all sealing rings | 35 Nm |
| 7AZ Mounting, hydraulic lines | E70, E71 | M6 | 7.5 Nm | |
| 8AZ Dynamic Drive pressure line to power steering pump | E70, E71 | M16 | 37.5 Nm | |
| E70/N62TU | M6 | 8 Nm | ||
| 9AZ Dynamic Drive pressure line to screwed-in pulsation damper | E70/N52/M57T2 | M14 | 30 Nm | |
| 10AZ Dynamic Drive pressure line to removed pulsation damper | E70/N62TU | M16 | 35 Nm | |
| 11AZ Pressure line to cutting line | E70 | M16 | 30 Nm | |
| E70/N62TU | M6 | 8 Nm | ||
| 12AZ Dynamic Drive pressure line to engine support arm | E70/E71/M57T2 | M6 | 9.5 Nm | |
| 13AZ Dynamic Drive pressure line to crankcase | E70/N52K | M8 | Replace aluminum screws. Use only Helicoil made of aluminum for thread repairs. Jointing torque and angle of rotation must be observed without fail. |
|
| Jointing torque | 8 Nm | |||
| Torque angle | 45 ° | |||
| 14AZ Heat shield | E70, E71 | M6 | 8 Nm | |
| 15AZ Holder, return hose to front axle carrier |
E71 | M6 | 7.5 Nm | |
| 16AZ Flange screw connection | E71 | M6 | 8 Nm | |
| 17AZ Pressure hose to holder | E71 | M6 | 8 Nm | |
| 18AZ Bracket to crankcase | E71 | M12 | 66 Nm |