32 21 Steering Arms
WARNING: This page does not describe the selected car, but rather 7 other vehicles, including the 2010 BMW X3, 2009 BMW X3, 2008 BMW X3, 2007 BMW X3, and 2006 BMW X3. However, it is still accessible from the selected car via links, so may be relevant.
STEERING ARMS - TIGHTENING TORQUES
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Tie rod to ball joint (castle nut) | E21 | 60 Nm | ||
| 2AZ Tie rod / axial joint to rack | E21, E30 | Replace retaining plate | 75 Nm | |
| E34, E36 | Replace retaining plate | 71 Nm | ||
| E39, E52 | 71 Nm | |||
| E46, E85 / except S54, E86 / except S54 | 100 + 10 Nm | |||
| E53, E60, E61, E63, E64, E65, E66, E67, E83, E85 / S54, E86 / S54 | 110 Nm | |||
| 3AZ Tie rod end to steering knuckle / swivel bearing | E34 / Four Wheel Drive | Replace nut | 50 Nm | |
| E36 | Replace nut | 36 Nm | ||
| E38, E39, E52 | Replace nut | 65 Nm | ||
| E46, E85, E86 | Use of impact screwdriver not permitted! Replace nut | 65 Nm | ||
| E53, E60 / Four Wheel Drive, E61 / Four Wheel Drive, E67, E83 | Replace nut | 80 Nm | ||
| E60 / REAR END, E61 / REAR END, E63, E64, E65, E66 | Replace nut | 165 Nm | ||
| 4AZ Tie rod clamping screw | E38, E39 | 27 Nm | ||
| E12, E23, E24, E28, E30, E31, E32, E34 | 14 Nm | |||
| 5AZ Tie rod end to tie rod (clamping nut) | E34 / Four Wheel Drive, E36, E46, E85, E86 | 45 Nm | ||
| E39, E52, E53, E60, E61, E63, E64, E65, E66, E67, E83 | 51 Nm | |||
| 6AZ Steering drop arm to steering gear | E32, E34 / Four Wheel Drive | 59 Nm | ||
| E23 | M26 | Tightening value may be exceeded up to correct position to locking plate | at least 180 Nm | |
| E12, E23, E24, E28 | M22 | Tightening value may be exceeded up to correct position to locking plate | at least 140 Nm | |
| E31 | 70 Nm | |||
| E38, E39 | Note direction of screw thread. In direction of travel: from left on LHD or from right on RHD vehicle | 61 Nm | ||
| 7AZ Steering guide arm to front axle carrier | E39 | 62 Nm | ||
| E23, E24, E28, E31, E32, E34, E38 | M10 | 42 Nm | ||
| E12, E23, E24 | M12 | 85 Nm | ||
| 8AZ Track rod arm to strut | E12, E24(upto 5.82) | Bolts secured with: Wire | 55 Nm | |
| E23, E24 (from 5.82), E28 | Bolts secured with: Loctite No. 270 Clean threads of tapped bores and bolts. | 62 Nm | ||
| E31, E32, E34 | Bolts secured with: Loctite No. 270 Clean threads of tapped bores and bolts. | 110 Nm | ||
| E30 / M3 | Bolts secured with: Loctite No. 270 Clean threads of tapped bores and bolts. | 30 Nm | ||
| 9AZ Tie rod arm to control arm | E12, E23, E24 (up to 5.82) | 66 Nm | ||
| E30 / M3 | 66 Nm | |||
| E24 (from 5.82), E28, E31, E32, E34 | 93 Nm | |||
| 10AZ Leading strut to tie rod arm | E23 | 93 Nm | ||
| 11AZ Trailing strut to tie rod arm | E31, E32, E34 | 93 Nm |