24 00 Transmission In General
WARNING: This page is about a different car, the 2010 BMW X3, 2009 BMW X3, 2008 BMW X3, and 2007 BMW X3. However, it is still accessible from the selected car via links, so may be relevant.
TRANSMISSION IN GENERAL - TIGHTENING TORQUES
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Transmission to engine | ||||
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z |
M8 | 24 Nm | |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z |
M10 | 45 Nm | |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z |
M12 | 82 Nm | |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R |
M8 | 21 Nm | |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R |
M10 | 42 Nm | |
| Torx bolts | A4S 200R / A4S 70R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R |
M12 | 72 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M6 | 9 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M8 | 22 Nm | |
| Torx screws N62TU | GA6HP26Z | M8 | 19 Nm | |
| Torx screws N62TU | GA6HP26Z | M10 | 38 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M12 | 73 Nm | |
| Torx screws, steel N51/N52/N54/N47/N53/N43/N45K | GA6HP19Z / GA6L45R | M8 | 19 Nm | |
| Torx screws, steel N51/N52/N54/N43/N47/N53/N52K | GA6HP19Z / GA6L45R | M12 | 66 Nm | |
| 2AZ Transmission to engine N51/N52/N54/N53/N52K Aluminium screws are marked blue |
GA6HP19Z / GA6L45R | Replace screws Jointing torque and angle of rotation must be observed without fail | ||
| GA6HP19Z / GA6L45R | M10x30 | Jointing torque | 20 Nm | |
| Torque angle | 90-110° | |||
| GA6HP19Z | M10x85 | Jointing torque | 20 Nm | |
| Torque angle | 180-200° | |||
| GA6HP19Z | M12 | Jointing torque | 34 Nm | |
| Torque angle | 90-110° | |||
| GA6HP19Z / GA6L45R | M12x76 | Jointing torque | 25 Nm | |
| Torque angle | 130° | |||
| 3AZ Reinforcement shell to transmission/extension | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 60Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z |
M8 | 23 Nm | |
| 4AZ Cover plate for transmission | GA6HP19Z | M6 | 9 Nm |