37 14 Electric Components
WARNING: This page is about a different car, the 2013 BMW X5 M, 2012 BMW X5 M, 2011 BMW X5 M, and 2010 BMW X5 M. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATIONS - ELECTRIC COMPONENTS
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Bracket, ride height sensor, to body | E70, E70M // E71, E71M / E72 | M6 | 8 Nm | |
| 2AZ Bracket ride height sensor to rear axle support | E70, E70M / E71, E71M / E72 | M6 | 8 Nm | |
| 3AZ Ride height sensor to holder | E70, E70M / E71, E71M / E72 | M5 | 5 Nm | |
| 4AZ Sensor lever, ride height sensor to jointed rod | E70, E70M / E71, E71M / E72 | M6 | Replace nut | 8 Nm |
| 5AZ Jointed rod to upper wishbone | E70, E70M / E71, E71M / E72 | M6 | Replace nut | 8 Nm |
| 6AZ Jointed rod to swinging arm | E70, E70M / E71, E71M / E72, | M6 | Replace nut | 8 Nm |
| 7AZ Acceleration sensor to body | E70, E70M / E71, E71M | M6 | 8 Nm | |
| 8AZ Control unit Dynamic Drive ECU to cockpit support structure | E70, E71 | M5x15 | 6 Nm | |
| 9AZ Valve block to holder | E70, E70M / E71, E71M / E72 | M6 | 8 Nm | |
| 10AZ Holder, valve block, to body | E70, E70M / E71, E71M / E72 | M6 | Replace nuts | 8 Nm |
| 11AZ Dynamic Drive pressure line to valve block | E70, E71 | 35 Nm | ||
| 12AZ Return line to valve block | E70, E71 | 40 Nm | ||
| 13AZ Control lines for oscillating motor, front, to valve block | E70, E71 | M14 | 35 Nm | |
| 14AZ Control lines for oscillating motor, rear, to valve block | E70, E71 | M14 | 35 Nm | |
| 15AZ Connecting nuts, hydraulic lines (pressure line / control lines) | E70,, E71 | 30 Nm | ||
| 16AZ Connecting nuts, hydraulic lines (return) | E70 | 35 Nm | ||
| 17AZ Line holder / pipe holder / holder | E70 / E71 / E72 | M6 | 8 Nm | |
| E70 / E71 / E72 | M8 | 20.5 Nm | ||
| 18AZ Control lines to oscillating motor | E70, E70M / E71, E71M | 30 Nm | ||
| 19AZ Heat shield to rear axle carrier | E70, E70M / E71, E71M / E72 | M10 | 38 Nm | |
| E70, E70M / E71, E71M / E72, | M6 | 8 Nm | ||
| 20AZ Retaining bar, stabiliser, to front axle carrier | E70, E70M / E71, E71M / E72 | M10 | 56 Nm | |
| 21AZ Retaining bracket, anti-roll bar to rear axle support | E70, E70M / E71, E71M / E72 | M10 | 56 Nm | |
| 22AZ Screw pins for pipe holder | E70, E70M / E71, E71M / E72 | Replace screw pins | 1.5 Nm | |
| 23AZ Spring-type actuator to oscillating motor, front | E70 | 30 Nm | ||
| 24AZ Pressure relief valve to oscillating motor, front | E70 | 14 Nm | ||
| 25AZ Line holder for control lines to front axle oscillating motor | E70 / E71 | 3 Nm | ||
| 26AZ Lines to spring-type actuator | E70 | 14 Nm | ||
| 27AZ Block screw connection, hydraulic lines | E70, E70M / E71, E71M | 12 Nm |