Special tools required
WARNING: This page is about a different car, the 2010 BMW M6, 2009 BMW M6, 2008 BMW M6, 2007 BMW M6, and 2006 BMW M6. However, it is still accessible from the selected car via links, so may be relevant.
SPECIAL TOOLS REFERENCE CHART
| Type | Engine | Adapter Y from 17-0100 TESTER |
|---|---|---|
| E60/E61/E63/E64 | All | 17 0 113 |
| E65/E66 | M54/N52/N62/N62T/N73 | 17 0 105 |
| E65/E66 | M57S/M57T/M67/M67T | 17 0 113 |
| E70/E71/E72 | All | 17 0 113 |
| E81/E82/E84/E87/E88/E89 | All | 17 0 113 |
| E83 | M54/N46/N52K | 17 0 105 |
| E83 | M47S/M57S/M57T/M57Y/N47 | 17 0 113 |
| E85/E86 | All | 17 0 105 |
| E90/E91/E92/E93 | All | 17 0 113 |
| F01/F02/F03/F04/F07/F10 | All | 17 0 113 |
| R50/R52 | W10 | 17 0 107 and 17 0 102 |
| R50 | W17 | 17 0 109 |
| R52/R53 | W11 | 17 0 109 |
| R55/R56/R57/R60 | All | 17 0 109 |
| F25 | All | 17 0 113 |
IMPORTANT:
Lifetime coolant filling:
Never reuse used coolant!
When replacing and removing components which rely on the corrosion protection effect of the coolant, it is essential to change the coolant. The cooling system must therefore be drained and refilled.
In the case of other removal work involving the draining of part quantities of coolant, replace these quantities which have been drained with new coolant.
Never reuse used coolant!
When replacing and removing components which rely on the corrosion protection effect of the coolant, it is essential to change the coolant. The cooling system must therefore be drained and refilled.
In the case of other removal work involving the draining of part quantities of coolant, replace these quantities which have been drained with new coolant.
IMPORTANT:
You must protect the alternator against contamination by coolant when carrying out repair work on the cooling circuit.
Cover alternator with suitable materials.
Failure to comply with this procedure may result in an alternator malfunction.
Cover alternator with suitable materials.
Failure to comply with this procedure may result in an alternator malfunction.
Note on ordering:
- Workshop equipment
- Workshop equipment catalogue
- Filler unit no. 81 39 2 152 473
- Collecting vessel no. 81 49 2 152 347
- Adapter: 17-0100 TESTER
IMPORTANT:
Risk of slipping due to coolant on the floor.
Danger of injury!
Danger of injury!
Catch and dispose of emerging coolant in drip tray (1) and if necessary special tool 00-2030 DEVICE (universal hydraulic lifting equipment).
Recycling:
Observe country-specific waste disposal regulations.
IMPORTANT:
Check all the coolant hoses before filling the cooling system with the vacuum filling unit.
If necessary, replace damaged and porous coolant hoses.
If necessary, replace damaged and porous coolant hoses.
- 1) Filling unit with vacuum meter and shut-off valves
- 2) Filler hose
- 3) Coolant container
- 4) Venturi nozzle
- 5) Compressed air connection (max. 6 bar)
- 6) Outgoing-air hose (lead outgoing-air hose into a collecting container)