13 51 017 Removing and installing or replacing high-pressure fuel pump (N54, N53)

WARNING: This page is about a different car, the 2010 BMW 135i, 2009 BMW 135i, and 2008 BMW 135i. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

11 8 610
13 5 020
13 5 281
13 5 282
32 1 270

See ENGINE- SPECIAL TOOLS .

See FUEL SYSTEM - SPECIAL TOOLS .

See STEERING AND WHEEL ALIGNMENT - SPECIAL TOOLS .

WARNING: Observe warning on cylinder head cover.
Disconnect battery negative terminal (risk of fire due to short-circuiting on removal). See 12 00... INSTRUCTIONS FOR DISCONNECTING AND CONNECTING BATTERY (CONVERTIBLE) or 12 00... INSTRUCTIONS FOR DISCONNECTING AND CONNECTING BATTERY (COUPE).
Electric fuel pump starts up automatically each time door is opened!
Carry out installation work on fuel system only with coolant temperature below 40°C.

IMPORTANT: Wear full face guard and protective gloves.
Fuel can emerge spontaneously at high velocity when the high-pressure line is released!

IMPORTANT: Adhere to conditions of absolute cleanliness when working on the high-pressure fuel system.
Introduced contaminants can cause malfunctions in the system!

Do not allow any dirt particles or foreign bodies to get into the system.
Remove all traces of dirt before removing pipes or individual components.
Use only fluff-free cloths.
Seal all fuel system openings with protective caps or plugs.

Necessary preliminary tasks:

Remove throttle body. See 13 54 030 Removing and installing/sealing throttle valve assembly (N54) .

Apply silicone-free multifunction spray (part number 83 23 0 418 567) on to supports (1) of base well bracket (2). Unplug connector (3) and (4) from base well. Slide base well (2) in direction of arrow.

Fig 1: Applying Silicone-Free Multifunction Spray On Base Well Bracket Supports

Courtesy of BMW OF NORTH AMERICA, INC.

Fig 2: Inserting Special Tools (00 7 300) In Base Well Mounting Points

Courtesy of BMW OF NORTH AMERICA, INC.

Insert special tool 00 7 300 in mounting points (1) on base well.

NOTE: Place tips of special tool 00 7 300 between retainers (2) and then center (arrow).

Detach base well (1) from bracket (2) with special tool 00 7 300.

Fig 3: Removing Base Well From Bracket Using Special Tool (00 7 300)

Courtesy of BMW OF NORTH AMERICA, INC.

Unlock connector (1) and remove. Unlock and detach fuel line (2). Catch and dispose of escaping fuel.

Fig 4: Identifying Plug And Fuel Line

Courtesy of BMW OF NORTH AMERICA, INC.

Seal fuel lines with special tools 13 5 281 and 13 5 282.

Fig 5: Identifying Seal Fuel Lines With Special Tools 13 5 281 And 13 5 282

Courtesy of BMW OF NORTH AMERICA, INC.

Slacken nut (1).

Release screw (2).

Installation:

Replace aluminum screw.

Remove feed line (3).

Fig 6: Slacken Nut And Remove Feed Line

Courtesy of BMW OF NORTH AMERICA, INC.

Seal feed line with matching plug from special tool kit 32 1 270.

Fig 7: Seal Feed Line With Matching Plug From Special Tool Kit 32 1 270

Courtesy of BMW OF NORTH AMERICA, INC.

WARNING: Wear full face guard and protective gloves.

Slacken nut (1).

Fig 8: Identifying Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Undo screws (1) and raise acoustic cover (2) in front area.

Fig 9: Raising Acoustic Cover In Front Area

Courtesy of BMW OF NORTH AMERICA, INC.

Slacken nut (1).

Fig 10: Identifying Slacken Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Seal fuel line connections of high pressure pump (1) with matching plugs from set of special tools 32 1 270.

Fig 11: Identifying High-Pressure Pump With Special Tool Kit 32 1 270

Courtesy of BMW OF NORTH AMERICA, INC.

Release bolts with special tool 11 8 610. Detach high pressure pump (1) and remove. Engine oil can escape when pump is detached; have a cleaning cloth ready.

Fig 12: Identifying High-Pressure Pump With Screws And Special Tool 11 8 610

Courtesy of BMW OF NORTH AMERICA, INC.

Installing high pressure pump: Installation of high pressure pump is described separately from removal.

Replace sealing ring (1). Clean contact surfaces.

Replacement: For better installation, turn the journal of the new high pressure pump to the position of the old high pressure pump.

Fig 13: Identifying Sealing Ring

Courtesy of BMW OF NORTH AMERICA, INC.

When installing, turn high-pressure pump (1) if necessary in direction of arrow until bores for screws are flush.

Fig 14: Identifying High-Pressure Pump

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Tighten screws of high-pressure pump (1) with special tool 11 8 610 hand-tight only .

Only hand-tighten screws (1) of high pressure pump (2) with special tool 11 8 610.

This helps ensure that no strain is produced when the high pressure line is tightened.

Copper seals that may be fitted on the high pressure line are no longer needed and must be removed.

If reusing pressure line, lightly grease threads of pressure connections. Threads of new pressure lines are already coated.

Fig 15: Identifying High Pressure Pump With Screws

Courtesy of BMW OF NORTH AMERICA, INC.

Only hand-tighten nut (1).

Fig 16: Identifying Hand-Tightened Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Only hand-tighten nut (1).

Fig 17: Identifying Hand-Tightened Nut

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Feed lines with soldered holder must be replaced by new version with elastomer clamp holder. Observe installation position of fuel low-pressure sensor. Lines for solenoid switches are laid behind fuel line.

Install feed line (3).

Only hand-tighten nut (1)! Tighten screw (2). Replace aluminum screw.

Tightening torque 13 53 9AZ.

Fig 18: Identifying Fuel Line Connection

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down screws with special tool 11 8 610. Tightening torque 13 51 1AZ.

Fig 19: Identifying Screws Of High-Pressure Pump With Special Tool 11 8 610

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten nut (1). Tightening torque 13 53 7AZ.

Fig 20: Identifying Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down nut (1) with special tool 13 5 020. Tightening torque 13 53 7AZ .

Fig 21: Identifying Nut

Courtesy of BMW OF NORTH AMERICA, INC.

Tighten down nut (1) with special tool 13 5 020. Tightening torque 13 53 6AZ .

Fig 22: Tightening Down Nut Using Special Tool (13 5 020)

Courtesy of BMW OF NORTH AMERICA, INC.

Install and lock connector (1).

Fig 23: Identifying Connector

Courtesy of BMW OF NORTH AMERICA, INC.

Slide base well (2) on to bracket (1) as far as it will go. Install and lock connector (3) and (4).

Fig 24: Applying Silicone-Free Multifunction Spray On Base Well Bracket Supports

Courtesy of BMW OF NORTH AMERICA, INC.

Assemble engine.

Check fuel system for leaks.

Check function of DME.