23 00 018 Removing and installing transmission (GS6-53DZ) N54

WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2010 BMW 535xi, 2010 BMW 535i, 2009 BMW 535xi, 2009 BMW 535i, and 2008 BMW 535xi. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

IMPORTANT: After completion of work, check GEAR OIL LEVEL .
Use only the approved gear oil.

Failure to comply with this requirement will result in serious damage to the manual transmission.

IMPORTANT: Aluminium screws/bolts must be replaced each time they are released .
Aluminium screws/bolts are permitted with and without color coding (blue).
For reliable identification:
Aluminium screws/bolts are not magnetic .
Jointing torque and angle of rotation must be observed without fail (risk of damage) .

Necessary preliminary tasks:

DISCONNECT BATTERY
Remove REINFORCEMENT PLATE
Remove EXHAUST SYSTEM
Support engine with lifter

Remove heat shields (1) and (2).

Fig 1: Identifying Heat Shields

Courtesy of BMW OF NORTH AMERICA, INC.

Release bolts (1).

Disconnect connector (2).

Steel screws, tightening torque 23 00 1AZ .

Aluminium screws, tightening torque 23 00 2AZ .

Release aluminium screws with special tool 00 9 010.

Fig 2: Identifying Connector And Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

Unclip cable (1) from holder.

Release screw (2) and remove holder (3).

NOTE: Illustration similar

Fig 3: Identifying Cable, Screw And Holder

Courtesy of BMW OF NORTH AMERICA, INC.

Release bolts (1).

Remove holder (2).

Fig 4: Identifying Transmission Bolts And Holder

Courtesy of BMW OF NORTH AMERICA, INC.

Disconnect plug connection (1) from reversing light switch.

Release cable from retainers.

Fig 5: Identifying Plug Connection

Courtesy of BMW OF NORTH AMERICA, INC.

Supporting transmission:

Support transmission with special tools 23 4 050, 00 2 030.

Secure transmission to mounting with tensioning strap (1).

Tasks are described in TRANSMISSION BRACKET .

After completion of work, check transmission oil level.

Fig 6: Identifying Special Tools (00 2 030) And (23 4 050)

Courtesy of BMW OF NORTH AMERICA, INC.

Remove TRANSMISSION CROSS-MEMBER .

Release screws.

Remove transmission support block.

Tightening torque 22 32 2AZ .

Fig 7: Locating Transmission Support Block Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

Remove propeller shaft from transmission.
Release center bearing.
Tie propeller shaft to one side.

Tasks are described in Removing PROPELLER SHAFT .

NOTE: Pressure line of clutch slave cylinder remains connected.

IMPORTANT: Slowly relieve tension on clutch slave cylinder otherwise air is drawn in through sealing sleeve.

Release nuts and remove clutch slave cylinder.

Tightening torque 21 52 5AZ .

Fig 8: Locating Clutch Slave Cylinder Nuts

Courtesy of BMW OF NORTH AMERICA, INC.

Lever out retainer (1).

Disengage shift rod (2).

Installation:

Grease shift rod.

Grease, refer to MANUAL TRANSMISSION - OPERATING FLUIDS .

Make sure shims (3) are in correct position.

Fig 9: Disengaging Shift Rod

Courtesy of BMW OF NORTH AMERICA, INC.

Release and remove bearing pins (1) in direction of arrow.

Fig 10: Removing Bearing Pins

Courtesy of BMW OF NORTH AMERICA, INC.

Lift out shift arm (1).

Installation:

Grease bearing pins (1).

Grease,

refer to MANUAL TRANSMISSION - OPERATING FLUIDS .

Fig 11: Lifting Out Shift Arm

Courtesy of BMW OF NORTH AMERICA, INC.

Release screws.

Installation:

Tightening torque, steel screws 23 00 1AZ .

Tightening torque, aluminium screws 23 00 2AZ . Screws: 3/4/5/9/10 (screw 3 only present on N54).

IMPORTANT: Do not allow the transmission to hang off from the transmission input shaft as this will deform the clutch plate. Pull out transmission towards rear and remove.

Fig 12: Transmission Housing Bolts Tightening/Loosening Sequence

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Secure angle of rotation special tool 00 9 120 with magnet 00 9 130 to floor plate. Screw down aluminium screws according to angle of rotation. Angle of rotation 23 00 2AZ .

Fig 13: Identifying Special Tools (00 9 130) And (00 9 120)

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Check that dowel sleeves are correctly seated.

Replace damaged dowel sleeves.

Ensure correct position of cover plate.

Fig 14: Identifying Correct Position Of Cover Plate

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Check lubrication of transmission input shaft for sticky consistency. If grease is sticky, clean input shaft and REPLACE CLUTCH PLATE .

Check clutch plate for friction rust in splines and REPLACE if necessary.

Mechanically remove existing grease and lining abrasion from splines of clutch plate (with a cloth).

Fig 15: Locating Input Shaft Splines

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Greasing specification:

Remove and clean RELEASE BEARING AND RELEASE LEVER .
Push on grease scraper ring 21 2 240 as far as it will go.
Grease splines (1) of input shaft with a brush. refer to MANUAL TRANSMISSION - OPERATING FLUIDS .
Detach grease scraper ring.
Lightly grease guide sleeve for release bearing.

Fig 16: Identifying Special Tools (21 2 240) And (21 2 221)
Courtesy of BMW OF NORTH AMERICA, INC.