24 00 Transmission In General
WARNING: This page is about a different car, the 2006 BMW 760i. However, it is still accessible from the selected car via links, so may be relevant.
TRANSMISSION IN GENERAL TIGHTENING TORQUES
| - | Type | Thread | Tightening specification | Measure |
|---|---|---|---|---|
| 1AZ Transmission to engine | - | - | - | - |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M8 | - | 24 Nm |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M10 | - | 45 Nm |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M12 | - | 82 Nm |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M8 | - | 21 Nm |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M10 | - | 42 Nm |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M12 | - | 72 Nm |
| Torx bolts | GA6HP19Z / GA6HP26Z | M6 | - | 9 Nm |
| Torx bolts | GA6HP19Z / GA6HP26Z | M8 | - | 22 Nm |
| Torx screws N62TU | GA6HP26Z | M8 | - | 19 Nm |
| Torx screws N62TU | GA6HP26Z | M10 | - | 38 Nm |
| Torx bolts | GA6HP19Z / GA6HP26Z | M12 | - | 73 Nm |
| Torx screws, steel N51/N52/N54/N47/N53/N43/N45K |
GA6HP19Z / GA6L45R | M8 | - | 19 Nm |
| Torx screws, steel N51/N52/N54/N43/N47/N53/N52K |
GA6HP19Z / GA6L45R | M12 | - | 66 Nm |
| 2AZ Transmission to engine N51/N52/N54/N53/N52K Aluminum screws are marked blue |
GA6HP19Z / GA6L45R | - | Replace screws Jointing torque and angle of rotation must be observed without fail | - |
| - | GA6HP19Z / GA6L45R | M10x30 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z | M10x85 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 180-200° |
| - | GA6HP19Z | M12 | Jointing torque | 34 Nm |
| - | - | - | Torque angle | 90-110° |
| - | GA6HP19Z / GA6L45R | M12x76 | Jointing torque | 25 Nm |
| - | - | - | Torque angle | 130° |
| 3AZ Reinforcement shell to transmission/extension | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M8 | - | 23 Nm |
| 4AZ Cover plate for transmission | GA6HP19Z | M6 | - | 9 Nm |