31 12 Control Arms and Struts
WARNING: This page is about a different car, the 2008 BMW Alpina and 2007 BMW Alpina. However, it is still accessible from the selected car via links, so may be relevant.
TORQUE SPECIFICATION - CONTROL ARMS AND STRUTS
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Tension strut to front axle support | E12, E24 / until 5.82 | tighten in normal position | 80 Nm | |
| E23 | tighten in normal position | 135 Nm | ||
| E39, E52 | tighten in normal position | 110 Nm | ||
| E53 | Replace screw tighten in normal position | 165 Nm | ||
| E60, E61, E63, E64, E65, E66, E67 | M12 10.9 | Replace screw & nut tighten in normal position | ||
| Jointing torque | 100 Nm | |||
| Torque angle | 90 ° | |||
| E83 | Replace screw tighten in normal position | |||
| Jointing torque | 165 Nm | |||
| Torque angle | 90 ° | |||
| 2AZ Control arm to front axle support | E24 / from 5.82, E28, E31, E32, E34, E38, E39 / 8 cyl. | tighten in normal position | 77.5 Nm | |
| E39 / 6 cyl., E52 | tighten in normal position | 110 Nm | ||
| E12, E21, E23, E24 / until 5.82 | tighten in normal position | 85 Nm | ||
| E53, E60, E61, E63, E64, E65, E66, E67, E83 | M12 10.9 | Replace screw & nut tighten in normal position | ||
| Jointing torque | 100 Nm | |||
| Torque angle | 90±15 ° | |||
| 3AZ Control arm (ball joint) on front axle support | E30 | Replace nut | 85 Nm | |
| E36, E46 | Replace nut | 90 Nm | ||
| E30 / Four Wheel Drive | Replace nut | 100 Nm | ||
| E85, E86 | M14x1.5 | Replace nut | 80 Nm | |
| 4AZ Control arm to spring strut | E21, E30 | 65 Nm | ||
| 5AZ Control arm to pivot mount/spring strut | E30 / Four Wheel Drive | 85 Nm | ||
| E30 / Four Wheel Drive | Polystop nut | 93 Nm | ||
| E34 / Four Wheel Drive | 80 Nm | |||
| 6AZ Control arm on steering knuckle/swivel bearing | E36, E46, E85, E86 | Use of impact screwdriver not permitted! | 65 Nm | |
| Replace nut | ||||
| E38 | Replace nut | 93 Nm | ||
| E39, E53, E52, E83, E60 / Four Wheel Drive, E61 / Four Wheel Drive, E67 | Replace nut | 80 Nm | ||
| E60 / REAR END, E61 / REAR END, E63, E64, E65, E66 | Replace nut | 165 Nm | ||
| 7AZ Bracket for control arm to engine carrier | E30 | 42 Nm | ||
| E36 | 47 Nm | |||
| E46 | Replace screws | 59 Nm | ||
| E85, E86 | M10 10.9 | Replace screws | 56 Nm | |
| 8AZ Ball joint for control arm to front axle carrier | E34 / Four Wheel Drive, E46 / Four Wheel Drive | 77 Nm | ||
| 9AZ Control arm to ball joint | E34 / Four Wheel Drive, E46 / Four Wheel Drive | 80 Nm | ||
| 10AZ Control arm holder to front axle support | E34 / Four Wheel Drive | 47 Nm | ||
| E46 / Four Wheel Drive | Replace screws | 59 Nm | ||
| 11AZ Pressure strut to body | E24 / from 5.82, E28 | tighten in normal position | 130 Nm | |
| 12AZ Traction strut on tie rod lever/steering knuckle/swivel bearing | E24, E28 / from 5.82, E31, E32, E34, E38 | 93 Nm | ||
| E39 | 80 Nm | |||
| 13AZ Pressure strut to connecting pipe/front axle support | E31, E32, E34, E38, E39 | tighten in normal position | 127 Nm | |
| 14AZ Pressure strut to cruciform reinforcement | E31 | tighten in normal position | 127 Nm | |
| 15AZ Connecting pipe to body | E31, E32, E34 | 127 Nm | ||
| 16AZ Connecting pipe support to body | E31, E32, E34 | 59 Nm | ||
| 17AZ Connecting pipe to trailing spring mount | E24 / from 5.82, E28 | 60 Nm | ||
| 18AZ Leading strut to tie rod arm | E23 | 85 Nm | ||
| 19AZ Tension strut on steering knuckle/swivel bearing | E39, E52, E67 | 80 Nm | ||
| E60 / REAR END, E61 / REAR END, E63, E64, E65, E66 | 165 Nm | |||
| 20AZ Tension strut to guide joint | E53, E83 | Replace nut | 80 Nm | |
| E60 / Four Wheel Drive, E61 / Four Wheel Drive | Replace nut | 165 Nm | ||
| 21AZ Guide joint to swivel bearing | E53, E60 / Four Wheel Drive, E61 / Four Wheel Drive, E83 | Replace screws | 60 Nm |