26 11 160 Replacing Constant-Velocity Joint For Propeller Shaft

WARNING: This page is about a different car, the 2008 BMW 760Li, 2007 BMW 760Li, and 2006 BMW 760Li. However, it is still accessible from the selected car via links, so may be relevant.

Special tools required:

23 1 040
24 1 040
26 1 070
26 1 110

Remove propeller shaft. See 26 11 000 REMOVING AND INSTALLING COMPLETE PROPELLER SHAFT

Lift out retainer.

Installation:

Replace retaining ring.

Fig 1: Locating Retaining Ring

Courtesy of BMW OF NORTH AMERICA, INC.

Drive out knurled pin.

Installation:

Install shims (1).

Fig 2: Identifying Shims

Courtesy of BMW OF NORTH AMERICA, INC.

Press gaiter off constant velocity joint.

Installation:

Inject new grease into constant velocity joint from rubber gaiter and flange sides.

Grease, refer to BMW Parts Service.

Insert sealing washer (1) in constant velocity joint.

Fig 3: Inserting Sealing Washer In Constant Velocity Joint

Courtesy of BMW OF NORTH AMERICA, INC.

Detach constant velocity joint with special tool 26 1 070 or 26 1 110. See 26 1 110 REMOVAL DISK .

Fig 4: Detaching Constant Velocity Joint With Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Drive on constant velocity joint with special tool 23 1 040 or 24 1 040 as far as it will go.

Fig 5: Identifying Special Tools

Courtesy of BMW OF NORTH AMERICA, INC.

Installation:

Shoulder (1) for sealing washer must point to gaiter.

Toothing must be free from grease.

Thread locking: apply Loctite 648.

IMPORTANT:

Keep Loctite out of balls paths.

Clean toothing and apply a light coating of oil.

Fig 6: Identifying Shoulder

Courtesy of BMW OF NORTH AMERICA, INC.

Special tools required:

23 1 160
26 1 110
26 1 121
26 1 122
31 2 102
31 2 104

Necessary preliminary tasks:

Remove propeller shaft. See 26 11 000 REMOVING AND INSTALLING COMPLETE PROPELLER SHAFT .

Lever sealing cap (1) with screwdriver (2) out of constant - velocity joint (3).

NOTE: Replace sealing cap (1) with seal.

Fig 1: Identifying Lever Sealing Cap

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE:

Installation sequence 1 = Constant-velocity joint

2 = Seal

3 = Sealing cap

Fig 2: Identifying Installation Sequence Of Components

Courtesy of BMW OF NORTH AMERICA, INC.

Lift off retainer

Installation:

Replace circlip.

Fig 3: Locating Circlip

Courtesy of BMW OF NORTH AMERICA, INC.

Force cap off constant velocity joint.

Installation:

Insert sealing washer (1) into constant-velocity joint.

Fig 4: Inserting Sealing Washer In Constant Velocity Joint

Courtesy of BMW OF NORTH AMERICA, INC.

Detach constant-velocity joint (1) with special tool 26 1 110 and commercially available special tool (2). See 26 1 110 REMOVAL DISK .

Fig 5: Identifying Constant-Velocity Joint & Special Tool

Courtesy of BMW OF NORTH AMERICA, INC.

Release clamp (1) and detach cap with gaiter.

Push on new cap with gaiter.

NOTE: Do not tighten down clamp (1) yet.

Fig 6: Identifying Clamp

Courtesy of BMW OF NORTH AMERICA, INC.

Mount constant-velocity joint with special tool 23 1 160 up to stop.

Align bores of constant velocity joint and cap to each other.

Tighten down clamp on gaiter.

NOTE: Keep toothing free of grease.

Inject new grease into constant velocity joint from rubber gaiter and flange sides.

Fig 7: Identifying Special Tool (23 1 160)

Courtesy of BMW OF NORTH AMERICA, INC.

Press sealing cap with special tools 26 1 121, 26 1 122, 31 2 102 and 31 2 104 into constant-velocity joint (1).

NOTE: Align sealing cap and seal to bores of constant-velocity joint with screw.

Fig 8: Identifying Special Tools

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: Prepare special tools 31 2 102 and 31 2 104.

Fig 9: Identifying Special Tool (31 2 102) & (31 2 104)

Courtesy of BMW OF NORTH AMERICA, INC.

Push cap (1) onto constant-velocity joint (2).

Fig 10: Pushing Cap Onto Constant-Velocity Joint

Courtesy of BMW OF NORTH AMERICA, INC.