24 00 Transmission In General
WARNING: This page is about a different car, the 2007 BMW 530xi, 2007 BMW 525xi, 2006 BMW 530xi, and 2006 BMW 525xi. However, it is still accessible from the selected car via links, so may be relevant.
TRANSMISSION TIGHTENING SPECIFICATION
| Application | Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|---|
| 1AZ | Transmission to engine | - | - | - | - |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M8 | - | 24 Nm | |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M10 | - | 45 Nm | |
| Hex screws | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M12 | - | 82 Nm | |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M8 | - | 21 Nm | |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M10 | - | 42 Nm | |
| Torx bolts | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R | M12 | - | 72 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M6 | - | 9 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M8 | - | 22 Nm | |
| Torx screws N62TU | GA6HP26Z | M8 | - | 19 Nm | |
| Torx screws N62TU | GA6HP26Z | M10 | - | 38 Nm | |
| Torx bolts | GA6HP19Z / GA6HP26Z | M12 | - | 73 Nm | |
| Torx screws, steel N51/N52/N54/N47/N53/N43/N45K | GA6HP19Z / GA6L45R | M8 | - | 19 Nm | |
| Torx screws, steel N51/N52/N54/N43/N47/N53/N52K | GA6HP19Z / GA6L45R | M12 | - | 66 Nm | |
| 2AZ | Transmission to engine N51/N52/N54/N53/N52K Aluminium screws are marked blue | GA6HP19Z / GA6L45R | - | Replace screws Jointing torque and angle of rotation must be observed without fail | - |
| - | GA6HP19Z / GA6L45R | M10x30 | Jointing torque | 20 Nm | |
| - | - | - | Torque angle | 90-110 ° | |
| - | GA6HP19Z | M10x85 | Jointing torque | 20 Nm | |
| - | - | - | Torque angle | 180-200° | |
| - | GA6HP19Z | M12 | Jointing torque | 34 Nm | |
| - | - | - | Torque angle | 90-110 ° | |
| - | GA6HP19Z / GA6L45R | M12x76 | Jointing torque | 25 Nm | |
| - | - | - | Torque angle | 130° | |
| 3AZ | Reinforcement shell to transmission/extension | A4S 200R / A4S 270R / A4S 310R / A5S 300J / A5S 310Z / A5S 325Z / A5S 440Z / A5S 560Z / A5S 360R/A5S 390R / GA6HP19Z / GA6HP26Z / GA6HP32Z | M8 | - | 23 Nm |
| 4AZ | Cover plate for transmission | GA6HP19Z | M6 | - | 9 Nm |