36 10 300 Remove or install front or rear wheel

Special tools required

IMPORTANT: Observe safety instructions on raising the vehicle . See 00..... LIFTING VEHICLE WITH A LIFTING PLATFORM or 3611503 RESETTING RDC (TYRE PRESSURE CONTROL) .

When fitting all four wheels (e.g. when changing from summer to winter wheels), check the tire inflation pressure.

To avoid tire damage, advise the customer to check the tire inflation pressures on a regular basis.

Follow instructions on initializing RUN FLAT INDICATOR (RPA).

After completing installation, check again that all wheel bolts are tightened to specified torque.

Tightening torque 36 10 1AZ .

Observe the following procedure to prevent shift errors and imbalance:

Loosen wheel bolts.
Wheel positioned with valve facing down.
If several wheels are simultaneously removed, mark installation location of wheels on tires (e.g. with a piece of chalk).
Mark out wheel to wheel hub.
Mark out lockable wheel bolt in relation to wheel.
Release wheel bolts, remove wheel.

Fig 1: Identifying Wheel Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: The following contact faces must be free from grease and clean:

between brake disc and disc wheel
between brake disc and wheel hub

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver!

Remove dirt, grease residues and corrosion from contact surface (1) with a drill and special tool 36 1 250 .

NOTE: Degrease contact surface with universal cleaner.

If there are grease residues in the area of the wheel bolt bore, the brake disc must be removed . See 3411220 REMOVING AND INSTALLING OR REPLACING BOTH FRONT BRAKE DISCS or 3421320 REMOVING AND INSTALLING/RENEWING BOTH BRAKE DISCS and cleaned.

Fig 2: Removing Dirt, Grease Residues And Corrosion Between Brake Disc And Disc Wheel With A Drill And Special Tool (36 1 250)

Courtesy of BMW OF NORTH AMERICA, INC.

IMPORTANT: Do not operate special tool 36 1 250 with an impact screwdriver!

Remove dirt, grease residues and corrosion from contact surface (1) with a drill and special tool 36 1 250 .

NOTE: Degrease contact surface with universal cleaner.

Fig 3: Removing Dirt, Grease Residues And Corrosion Between Brake Disc And Wheel Hub With A Drill And Special Tool (36 1 250)

Courtesy of BMW OF NORTH AMERICA, INC.

Check brake disc retaining bolt (1) for secure seating.

IMPORTANT: Mounting bolt (1) must not under any circumstances protrude over contact surface (2) between brake disc and disc wheel.

Tightening torque brake disc retaining bolt:

FRONT AXLE 34 11 1AZ .

REAR AXLE 34 21 1AZ .

Fig 4: Identifying Brake Disc Mounting Bolt Seating Position And Between Brake Disc And Discwheel

Courtesy of BMW OF NORTH AMERICA, INC.

Apply a thin coat of grease to wheel centering (1) in disc wheel.

NOTE: Refer to WHEEL AND TIRES - OPERATING FLUIDS .

Fig 5: Identifying Wheel Centering In Disc Wheel

Courtesy of BMW OF NORTH AMERICA, INC.

Wheel bolts with taper:

Wheel bolt - galvanized
Wheel bolt - black chrome plated
Wheel bolt - black chrome plated and lockable
Lockable wheel bolt with adapter, black chrome-plated

NOTE: To release and tighten down lockable wheel bolts, use a matching adapter from special tool 36 1 300 .

Fig 6: Identifying Wheel Bolts

Courtesy of BMW OF NORTH AMERICA, INC.

Clean wheel bolts and check threads for damage, replace, if necessary.

Replace rusty wheel bolts.

IMPORTANT: Do not apply oil to wheel bolts.

IMPORTANT: Do not under any circumstances use an impact or power screwdriver to tighten down the wheel bolts (in diagonal sequence); this must be done by hand.

IMPORTANT: Disc wheel must rest uniformly against brake disc.
In the case of non-original BMW wheel studs/rims it may be necessary to retighten the wheel studs on account of settling properties.

Fit wheel bolts and evenly tighten crosswise by hand in order to center the disc wheel.

Tighten down wheel bolts in crosswise sequence with a calibrated torque wrench to prescribed tightening torque.

TIGHTENING TORQUE 36 10 1AZ .

Fig 7: Tightening Down Wheel Bolts In Crosswise Sequence With Calibrated Torque Wrench

Courtesy of BMW OF NORTH AMERICA, INC.

NOTE: For wheels with Styling 90 wheel cover.

The wheel cover can be removed for cleaning and removal of foreign objects.

Fit special tool 36 1 120 (3) as shown on rim (1) (near valve).

Engage removal fork of special tool 36 1 120 (3) in wheel cover (2).

Pull off wheel cover (2) with handle of special tool 36 1 120 (3).

Fig 8: Pulling Off Wheel Cover With Handle Of Special Tool (36 1 120)

Courtesy of BMW OF NORTH AMERICA, INC.