26 11 Propeller Shaft Complete
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT COMPLETE
| - | Type | Thread | Tightening specification | Measure |
|---|---|---|---|---|
| 1AZ Flexible disk to propeller shaft and transmission output flange Steel propeller shaft |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 8.8 | - | 48 Nm |
| - | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 10.9 | - | 64 Nm |
| - | E31/E38/E39/E46 | M14 | - | 140 Nm |
| - | E32/E34/E36/E38/E39 | - | M12 8.8 | 81 Nm |
| - | E60/E61/E63/E64 | M12 8.8 | - | 90 Nm |
| - | E32/E34/E36/E38/E39/E46/E53/E85 | M12 10.9 | - | 100 Nm |
| - | E60/E61/E63/E64 | M12 10.9 | Jointing torque | 55 Nm |
| - | - | - | Torque angle | 90° |
| - | E39 (M5)/E36 (M3)/E46 (M3), | M12 10.9 | - | 115 Nm |
| - | E65 | M12 10.9 | - | 90 Nm |
| Flexible disk to transmission output flange | E46/E39/E60/M57 only | - | Screw with rolled-on shim only | - |
| - | - | - | Jointing torque | 50 Nm |
| - | - | - | Torque angle | 90° |
| Flexible disk to transmission output flange | E65/E66/All except N73, M67 | - | Screw with rolled-on shim only | - |
| - | - | - | Jointing torque | 50 Nm |
| - | - | - | Torque angle | 90° |
| - | E60/E61/E63/E64/E65/E66/E67 | M12 10.9 | Double-stage flexible disc | - |
| - | - | - | Jointing torque | 50 Nm |
| - | - | - | Torque angle | 90° |
| Flexible disk on propeller shaft | E83 | M12 10.9 | Tighten via nut | 100 Nm |
| Flexible disk to transmission output flange | E83 | M12 10.9 | - | 90 Nm |
| Aluminum propeller shaft: Flexible disk to transmission output flange | E39/E60 | M12 10.9 | - | 100 Nm |
| Aluminum propeller shaft: Flexible disk on propeller shaft | E39/E60 | M12 10.9 | - | 90 Nm |
| - | E60/E61/E63/E64 | M10 10.9 | 64 Nm | - |
| - | E60 | M12 8.8 | - | 90 Nm |
| - | E63 (N52) | M12 | - | 110 Nm |
| Flexible disk to transmission output flange ZNS screws and nuts Shiny zinc coating All versions |
- | - | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | - |
| - | E60/E61/E63/E64/E85/E86/E87/E90/E91/E92/E93/E81 | M10 - 10.9 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 90° |
| - | E46/E53/E60/E61/E63/E64/E65/E83/E85/E86/E87/E90/E91/E92/E93/E70/E81 | M12-10.9 | Jointing torque | 55 Nm |
| - | - | - | Torque angle | 90° |
| - | E60/E61/E63/E64/E65 | M12-8.8 | Jointing torque | 30 Nm |
| - | - | - | Torque angle | 90° |
| 2AZ Coupling propeller shaft to transmission | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | M10 | - | 60 Nm |
| - | E32/E31 | M12 | - | 95 Nm |
| 3AZ Clamping ring for slide after installation in the car | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E87/E90/E91 | - | - | 10 Nm |
| - | E30/Four Wheel Drive | - | - | 22 Nm |
TIGHTENING TORQUE SPECIFICATION - PROPELLER SHAFT COMPLETE
| - | Type | Thread | Tightening specification | Measure |
|---|---|---|---|---|
| 4AZ Propeller shaft to drive flange (rear differential) | - | - | - | - |
| Version, universal joint: >Compression nut |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | Only finned nuts to higher tightening torque | 64 Nm |
| Version, universal joint: >Torx bolt |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | - | 85 Nm |
| Version, constant-velocity joint: >Torx bolt |
E46 (M3)/E38/E39/E46/E60/E83 (M57TU)/E63 (N52) | M10 | - | 70 Nm |
| Version, constant-velocity joint: >Compression nut |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M8 | - | 32 Nm |
| Compression nut | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | - | 64 Nm |
| Finned nut | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M8 | - | 43 Nm |
| Finned nut | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85 | M10 | - | 70 Nm |
| ZNS screws and nuts, shiny zinc coating All versions with universal or constant-velocity joint |
- | - | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | - |
| - | - | - | - | - |
| - | E83/E85/E86/E87/E90/E91/E92/E93/E81 | M10-10.9 screw with ribbed teeth | Jointing torque | 40 Nm |
| - | - | - | Torque angle | 45° |
| - | E46/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | M10 - 10.9 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 90° |
| - | - | - | - | - |
| - | E90/E91/E92 | M12x55- | Jointing torque | 55 Nm |
| - | E81/E87 | 10.9 | - | - |
| - | - | - | Torque angle | 90° |
| Screw with ribbed teeth | E85/M, E86 | M10x46-10.9 | Replace screws and shims | 70 Nm |
| 5AZ Pivot to center propeller shaft journal with Loctite (Version without slide) |
E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92 | - | - | 97 Nm |
| 6AZ Centre mount to body | E36/E38/E39/E46/E52/E53/E60/E61/E63/E64/E65/E66/E83/E85/E86/E87/E90/E91/E92/E93/E70/E81 | - | - | 21 Nm |
| 7AZ Flexible disk to front axle differential | E53 | M10 - 10.9 | - | 60 Nm |
| 8AZ Flexible disk on propeller shaft | E53 | M10 - 10.9 | - | 64 Nm |
| 9AZ Front propeller shaft to transfer box/front differential ZNS screws and nuts, shiny zinc coating |
- | - | Replace bolts and nuts Jointing torque and angle of rotation must be observed without fail | - |
| - | E60/E61/E90/E91/E92 | M8 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 45° |
| - | E46/E83 | M10 - 10.9 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 45° |
| - | E53/E70 | M10 - 12.9 | Jointing torque | 10 Nm |
| - | - | - | Torque angle | 90° |
| - | E46 | M10x1.5 10.9 | Jointing torque | 5 Nm |
| - | - | - | Torque angle | 90° |
| Universal joint | E70 | M10 - 10.9 | Jointing torque | 20 Nm |
| - | - | - | Torque angle | 45° |