23 11 Case and Cover
WARNING: This page is about a different car, the 2010 BMW 650i, 2009 BMW 650i, 2008 BMW 650i, 2007 BMW 650i, and 2006 BMW 650i. However, it is still accessible from the selected car via links, so may be relevant.
TIGHTENING TORQUE SPECIFICATION - CASE AND COVER
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Transmission housing, rear section/front section | B/C/D/E/F/G/H/I/7-speed SMG | 22 Nm | ||
| 2AZ Cover with guide tube/transmission case | B/C/D/E/F/G/H/I/7-speed SMG | M8 x 22 | 18 Nm | |
| B/C/D/E/F/G/H/I/7-speed SMG | M8 x 30 | 25 Nm | ||
| B/C/D/E/F/G/H/I/7-speed SMG | M6 | 10 Nm | ||
| 3AZ Bearing cap/sealing flange | B/C/D/E/F/G/H/I/7-speed SMG | 10.5 Nm | ||
| 4AZ Reverse gear wheel axle to intermediate housing | B/C/D/E/F/G/H/I/7-speed SMG | 49 Nm | ||
| 5AZ Retaining plate for reverse gear wheel axle to intermediate housing | B/C/D/E/F/G/H/I/7-speed SMG | 25 Nm | ||
| 6AZ Transmission closing plate | B/C/D/E/F/G/H/I/7-speed SMG | M6 | 8 Nm |
TIGHTENING TORQUE SPECIFICATION - CASE AND COVER
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 6AZ Reverse gear shaft to case | B/C/D/E/F/G/H/I/7-speed SMG | M8 | 25 Nm | |
| S5D 310Z/S5D 320Z | M8 | 20 Nm | ||
| B/C/D/E/F/G/H/I/7-speed SMG | M10 | 45 Nm | ||
| 7AZ Support for reverse gear shaft | B/C-transmission | M8 | 25 Nm | |
| 8AZ Bearing holder to rear housing section | B/C-transmission | M6 | 10 Nm | |
| 9AZ Retaining tabs for sealing cap | C-transmission | M6 | 10 Nm | |
| 10AZ Bearing on countershaft | B-transmission | M10 | 90 Nm | |
| C-transmission | M10 | 30 Nm | ||
| C-transmission | M10 | 60 Nm |
TIGHTENING TORQUE SPECIFICATION - CASE AND COVER
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 11AZ Screw plug to rear housing section | B/C/D/E/F/G/H/I/7-speed SMG | M20 | 60 Nm | |
| B-transmission | M16 | 40 Nm | ||
| B/C-transmission | M22 | 60 Nm | ||
| 12AZ Sealing caps to rear housing section | B/C-transmission | M6 | 10 Nm | |
| 13AZ Reversing bolt to reversing lever | ZFS-5-16/C-transmission | 43 Nm | ||
| 14AZ Clamping claw to rear housing section | ZFS-5-16/C-transmission | 33 Nm | ||
| 15AZ Screws on detent plate | ZFS-5-16/C-transmission | 9 Nm |