Section 597 (Engine - Repair - E90/E91 (-08); E92/E93 (N51/N52))
WARNING: This page does not describe the selected car, but rather 16 other vehicles, including the 2013 BMW 328xi, 2013 BMW 328i, 2012 BMW 328xi, 2012 BMW 328i, and 2011 BMW 328xi. However, it is still accessible from the selected car via links, so may be relevant.
- Engine, General
- Safety information for working on vehicles with automatic engine start-stop function (MSA)
- 11 00... Service - engine oil (N51)
- 11 00... Engine oil service (N52K)
- 11 00 Removing and installing/replacing acoustic cover (N51)
- 11 00 Removing and installing/replacing acoustic cover (N52/N52K)
- 11 00 Removing and installing/replacing ignition coil cover (N52K)
- 11 00 050 Removing and installing engine (N51)
- 11 00 050 Removing and installing engine (N52K)
- 11 00 670 Securing engine in installation position (N51)
- 11 00 670 Securing engine in installation position (N52K, N53)
- Engine identification
- Mounting engine on assembly stand (N51)
- Mounting engine on assembly stand (N52K)
- Cylinder Head And Cylinder Head Cover
- 11 12 000 Removing and installing/sealing cylinder head cover (N51)
- 11 12 000 Removing and installing/sealing cylinder head cover (N52K)
- 11 12 100 Removing and installing/sealing cylinder head (N51)
- 11 12 100 Removing and installing cylinder head (N52K)
- 11 12 101 Replacing cylinder head gasket (N51)
- 11 12 101 Replacing cylinder head gasket (N52K)
- 11 12 719 Resurfacing cylinder head sealing face (N51)
- 11 12 719 Resurfacing cylinder head sealing face (N52K)
- 11 12 729 Checking cylinder head for leaks (N51)
- 11 12 729 Checking cylinder head for water leaks (N52K)
- Oil Sump
- Housing Cover
- 11 14 005 Replacing front crankshaft seal (N51)
- 11 14 005 Replacing front crankshaft seal (N52K)
- 11 14 010 Replacing vacuum pump sealing cover (N51)
- 11 14 010 Replacing sealing cover for vacuum pump (N52K)
- 11 14 151 Replacing crankshaft seal (N52K) (up to 12/31/08)
- 11 14 151 Replacing crankshaft seal (N52K) on transmission side (from 1/1/09)
- 11 14 151 Replacing crankshaft seal on transmission side (N51) (up to 12/31/08)
- 11 14 151 Replacing radial crankshaft seal on transmission side (N51) (from 1/1/09)
- Crankshaft With Bearings
- 11 21 500 Replacing crankshaft (N51)
- 11 21 500 Replacing crankshaft (N52K)
- 11 21 505 Sealing crankcase lower section (N51)
- 11 21 505 Sealing crankcase lower section (N52K)
- 11 21 531 Replacing all crankshaft main bearings (N51)
- 11 21 531 Replacing all main crankshaft bearing shells (N52K)
- 11 21 571 Replacing roller ball bearing in crankshaft (N52K)
- Flywheel
- Vibration Damper
- Connecting Rod With Bearings
- Piston With Rings And Pin
- V-Ribbed Belt With TENSIONER / Deflect Element
- Camshaft
- 11 31 005 Checking camshaft timing
- 11 31 005 Checking timing of camshaft(s) (N52K)
- 11 31 025 Removing and installing/replacing intake camshaft (N51)
- 11 31 025 Removing and installing/replacing intake camshaft (N52K)
- 11 31 028 Removing and installing/replacing exhaust camshaft (N51)
- 11 31 028 Removing and installing/replacing exhaust camshaft (N52K)
- 11 31 051 Replacing timing chain (N51)
- 11 31 051 Replacing timing chain (N52K)
- 11 31 090 Installing and removing/replacing chain tensioner piston (N51)
- 11 31 090 Installing and removing/replacing chain tensioner piston (N52K)
- 11 31 505 Adjusting camshaft timing (N51)
- 11 31 505 Adjusting timing of camshaft(s) (N52K)
- Rocker Arm With Bearings Mount
- Valves With Springs
- 11 34 552 Removing and installing or replacing all valves (N51)
- 11 34 552 Removing and installing/replacing all valves (N52K)
- 11 34 560 Replacing all valve stem seals (N51)
- 11 34 560 Replacing all valve stem seals (N52K)
- 11 34 715 Replacing all valve springs (N51)
- 11 34 715 Replacing all valve springs (N52K)
- Variable Camshaft Timing
- Variable Valve Gear
- 11 37 005 Removing and installing/replacing eccentric shaft (N51)
- 11 37 005 Removing and installing/replacing eccentric shaft (N52K)
- 11 37 010 Removing and installing/replacing intermediate levers (N51)
- 11 37 010 Removing and installing/replacing intermediate levers (N52K)
- 11 37 020 Removing and installing/replacing positioning motor for eccentric shaft (N51)
- 11 37 030 Removing and installing/replacing eccentric shaft sensor (N51)
- Oil Supply
- Oil Pump With Filter And Drive
- 11 41 000 Removing and installing oil pump (N51)
- 11 41 000 Removing and installing/replacing oil pump (N52K)
- 11 41 010 Removing and installing/replacing chain module for oil pump/vacuum pump (N51)
- 11 41 010 Removing and installing/replacing chain module for oil pump/vacuum pump (N52K)
- 11 41 115 Removing and installing/replacing hydraulic valve (N52K)
- Oil Filter And Lines
- Water Pump With Drive
- Thermostat And Connections
- Intake Manifold
- Exhaust Manifold
- Vacuum Pump
- Emission Control, Oxygen Sensor