11 11 Engine Block
WARNING: This page is about a different variant/trim than selected.
11 11 Engine Block Fastener Tightening Specification
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 1AZ Main bearing screws | M10/M20/M30 | M10 | Replace, wash and oil screws | 60 N.m |
| M21 | M10 | Replace, wash and oil screws | 65 N.m | |
| S38/S14/ M40 / M42 / M43 / M43TU / M44 / M50 / M41 / M51 / S50 / S50 US | M10 | Replace, wash and oil screws | ||
| Jointing torque | 20 N.m | |||
| Torque angle | 50° | |||
| M47 / M57 | M10 | Replace, wash and oil screws | ||
| Jointing torque | 20 N.m | |||
| Torque angle | 70° | |||
| M47TU / M57TU | M10 | Replace, wash and oil screws | ||
| Jointing torque | 22 N.m | |||
| Torque angle | 90° | |||
| M67 | M12 | Replace, wash and oil screws | ||
| Jointing torque | 20 N.m | |||
| Torque angle | 200° | |||
| S54 | M10 | Replace, wash and oil screws | ||
| Jointing torque | 25 N.m | |||
| Torque angle | 50° | |||
| 2AZ Main bearing screws | M70 / S70 / M73 | M10 | Replace screws Do not wash off screw coating | |
| Jointing torque | 20 N.m | |||
| Torque angle | 70° | |||
| M60 / M62 | M10/M11 | Replace screws Do not wash off screw coating | ||
| M10/M11 | Jointing torque | 20 N.m | ||
| M10 | Torque angle | 70° | ||
| M11 | Torque angle | 100° | ||
| M54 / M56 / M52TU / M52 / with aluminum engine block | M10 | Replace, wash and oil screws | ||
| Jointing torque | 20 N.m | |||
| Torque angle | 70° | |||
| S52/M52/with cast iron engine block | M10 | Replace, wash and oil screws | ||
| Jointing torque | 20 N.m | |||
| Torque angle | 50° |
11 11 Engine Block Fastener Tightening Specification
| Type | Thread | Tightening specification | Measure | |
|---|---|---|---|---|
| 3AZ Taper screw mount on main bearing | ||||
| Screws and spacer bolts | M60 / M62 / M70 / S70 / M73 / S62 | M8 | Replace screws | |
| Jointing torque | 20 N.m | |||
| Torque angle | 45° | |||
| N62 / N62TU / N73 | M8 | 34 N.m | ||
| Threaded support sleeves | M70 / M60 / M62 / S70 / M73 / S62 | 10 N.m | ||
| N62 / N62TU / N73 | 6N.m | |||
| 4AZ Struts/bracing shell | M67 | M10.9 | 66 N.m | |
| M10 | 43 N.m | |||
| M8 | 22 N.m | |||
| 5AZ Drain plug for coolant in engine block | M14x1.5 | 25 N.m | ||
| 6AZ Main oil gallery seal plugs | M16x1.5 | 34 N.m | ||
| M 18x1.5 | 40 N.m | |||
| N62 / N62TU / N73 | M 18x1.5 | Insert screw with Loctite | 25 N.m | |
| N40 / N42 / N45 / N46 | M 16x1.5 | 36 N.m | ||
| Main oil gallery, rear (seal plugs with control valve) | M62 / S62 | M18x1 | 10 N.m | |
| 7AZ Oil spray nozzle on engine block | M6 | 10 N.m | ||
| Oil spray nozzle screwed into bearing seat (coat thread with Loctite 243) | M73 | M8x1 | 5 N.m | |
| Oil spray nozzle to engine block (banjo bolt) | M8x1 | 12 N.m | ||
| 8AZ Pressure holding valve to crankcase (1bar) | S54 / B32 | 20 N.m |