Overview - Oil Pan/Oil Pump
- Oil spray jet for piston cooling. Refer to OVERVIEW - PISTONS AND CONNECTING ROD .
- Bolt
- Replace after removing
- Tightening Specifications and Sequence. Refer to Fig 2.
- Oil Pan Lower Section
- Removing and Installing. Refer to OIL PAN LOWER SECTION, REMOVING AND INSTALLING .
- Intake Tube
- For the oil pump
- Replace after removing
- Bolt
- Replace after removing
- 8 Nm +90°
- Chain Sprocket
- For the oil pump
- Bolt
- Replace after removing
- 20 Nm +90°
- Bolt
- Oil Pan Upper Section
- Removing and Installing. Refer to OIL PAN UPPER SECTION, REMOVING AND INSTALLING .
- Alignment Sleeve
- Bolt
- Replace after removing
- Tightening Specifications and Sequence. Refer to Fig 3.
- Oil Tray
- Removing and Installing. Refer to OIL TRAY, REMOVING AND INSTALLING .
- Alignment Sleeve
- Alignment Sleeve
- Bolt
- Alignment Sleeve
- Seal
- Replace after removing
- Alignment Sleeve
- Bolt
- Replace after removing
- 8 Nm +90°
- Oil Pump
- Do not disassemble
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- O-Ring
- Replace after removing
- Seal
- Replace after removing
- Oil Drain Plug
- Oil the threads
- 30 Nm
- Oil Level Thermal Sensor -G266-
- Removing and Installing. Refer to Oil Level Thermal Sensor -G266-, REMOVING AND INSTALLING .
- Bolt
- Replace after removing
- Aluminum bolt : 3 Nm + 90°
- Steel bolt: pre-tightening: 2 Nm, final tightening: 9 Nm
- Seal
- Replace after removing
Depending on the version, aluminum or steel bolts may be installed.
Aluminum bolts:
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 17- | Install all the way by hand |
| 2. | -1 to 17- | 3 Nm |
| 3. | -1 to 17- | 90° additional turn |
Steel bolts:
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 17- | Install all the way by hand |
| 2. | -1 to 17- | 2 Nm |
| 3. | -1 to 17- | 9 Nm |
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in stages as follows:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -arrows- | Install all the way by hand |
| 2. | -1 and 2- | 3 Nm |
| 3. | -arrows- | 3 Nm in a diagonal sequence |
| 4. | -1 and 2- | 90° additional turn |
| 5. | -arrows- | Turn an additional 90° in a diagonal sequence |
Fig 4: Oil Pan Upper Section - Tightening Sequence (With The Lower Cover For The Camshaft Timing Chain Installed)
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 21- | Install all the way by hand |
| 2. | -20 and 21- | 3 Nm |
| 3. | -1 to 19- | 3 Nm |
| 4. | -20 and 21- | 90° additional turn |
| 5. | -1 to 19- | 90° additional turn |
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification |
|---|---|---|
| 1. | -1 to 19- | Install all the way by hand |
| 2. | -1 to 19- | 3 Nm |
| 3. | -1 to 19- | 90° additional turn |