Axle Beam Bonded Rubber Bushing, Replacing: Removing

WARNING: This page is about a different car, the 2022 Audi S3, 2022 Audi RS 3, 2022 Audi A3 Quattro, and 2022 Audi A3. However, it is still accessible from the selected car via links, so may be relevant.

-- Before starting the procedures, determine the curb weight position. Refer to VEHICLES WITH COIL SPRINGS, CHECKING THE CURB WEIGHT POSITION FOR AXLE ALIGNMENT .

-- Release the parking brake.

-- Remove the rear wheels. Refer to WHEELS AND TIRES .

-- Remove the outer stone chip protection on the rear axle. Refer to OUTER STONE CHIP PROTECTION, REMOVING AND INSTALLING .

Vehicle with Left Rear Level Control System Sensor -G76- with Clipped Lever:

Courtesy of AUDI OF AMERICA, LLC

-- Release the catch -5- in the direction of -arrow A- and pivot the sensor lever -4- upward in direction of -arrow B- and disengage from the axle beam.

Vehicle with Level Control System Sensor and Bolted Lever:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolt -1-.

-- Remove the lever from the Left Rear Level Control System Sensor -G76- -2- from the axle beam -3-.

Continuation for All Vehicles:

Courtesy of AUDI OF AMERICA, LLC

-- Free up the brake line -1- on the right mounting bracket -arrow- the clip is destroyed while doing this.

-- Free up the left and right wire -1- from the bracket -2- on the axle beam -arrows-.

Courtesy of AUDI OF AMERICA, LLC

-- Loosen the left and right bolt -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Place the Engine and Gearbox Jack: VAS6931 with the mounting plate and a suitable support underneath are secure with the corresponding tensioning strap.

-- Free up the wire -2- on the mounting bracket -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Carefully lower the rear axle using the Engine and Gearbox Jack: VAS6931 until it is possible to remove the bolt -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Position the special tool as shown:

Courtesy of AUDI OF AMERICA, LLC

1 - Hydraulic Press - Ball Joint Assembly Tools - Spindle: T10254/5

2 - Hydraulic Press - Ball Joint Assembly Tools - Nut: T10254/4

3 - Hydraulic Press: VAS6178 with Bearing Installer - Wheel Hub/Bearing Kit- Adapter 13: T10205/13

4 - Pneumatic/Hydraulic Foot Pump - Press Kit - Press Plate: T10495/3

5 - Pneumatic/Hydraulic Foot Pump - Press Kit - Pipe: T10495/2A

Pay attention to the tube contacts the axle beam, -arrow-.

6 - Pneumatic/Hydraulic Foot Pump - Press Kit - Thrust Piece: T10495/1

7 - Hydraulic Press - Ball Joint Assembly Tools - Nut: T10254/4

-- Connect the special tools as shown.

Courtesy of AUDI OF AMERICA, LLC

Hydraulic Press: VAS6178
Pneumatic/Hydraulic Foot Pump - Pressure Gauge: VAS6179/1
Pneumatic/Hydraulic Foot Pump: VAS6179

-- Pull the control knob on the pressure relief valve for the Pneumatic/Hydraulic Foot Pump: VAS6179 to level -1-.

Courtesy of AUDI OF AMERICA, LLC

The control knob must be in the position -1-. The setting is a maximum pressure of 200 bar (2, 900.76 psi). In position -2- (700 bar (10, 152.66 psi)) the nominal load of the spindle is exceeded.

CAUTION:

Risk of destroying components due to the pressure setting being too high.

- Never set the pressure greater that the specified (position 1 = 20 MPa).

CAUTION:

Risk of personal injury and property damage caused by the spindle breaking or the assembly tool deforming. Uncontrolled flying broken pieces possible.

- Wear safety gloves.

- Wear protective headgear with a visor.

- Pay attention when operating the foot pump, to not push the switch button in the lower position.

-- Carefully operate the Pneumatic/Hydraulic Foot Pump: VAS6179 while monitoring the pressure indicator on the Pneumatic/Hydraulic Foot Pump - Pressure Gauge: VAS6179/1 -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Make sure that the indicator stays in the green display area. Do not exceed the maximum permitted pressure of 200 bar (2, 900.76 psi).

-- Activate the pump and remove the bonded rubber bushing.