Front Seat, Removing With Faulty Seat Forward/Back Adjustment Motor

WARNING: This page is about a different car, the 2024 Audi S6 and 2024 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Follow the safety precautions. Refer to the appropriate service information .
To complete the procedure, a second technician is required to be at the following position. Refer to FRONT SEAT, REMOVING WITH FAULTY SEAT FORWARD/BACK ADJUSTMENT MOTOR - Remove the front seat from the vehicle with a second technician. .

Special tools and workshop equipment required

Trim Removal Wedge :3409

Fig 1: Identifying Trim Removal Wedge
Courtesy of AUDI OF AMERICA, LLC
Universal Vehicle Protector :VAS 871 001

TIP:

To lift out the front seat, the Seat Assembly Device :VAS 281 003 can be used. Pay attention to the accompanying instruction manual.

Driver/Front Passenger Seat Forward/Back Adjustment Motor Driver Seat Forward/Back Adjustment Motor -V28- /Front Passenger Seat Forward/Back Adjustment Motor -V31-, Checking

-- Move the front seat into its highest position.

To avoid unnecessary repair costs, check electrical and electronic components and wires before removing the front seat any more.

-- Perform the following tests:

Check the fuse. Refer to Wiring Diagram.
Check the voltage at the connector station and perform Fault Finding if necessary. Refer to Wiring Diagram.
Check the voltage on the seat forward/back adjustment motor. Refer to Wiring Diagram.
Check the voltage on the seat adjustment control head, and perform Fault Finding if necessary. Refer to Wiring Diagram.

-- Replace the fuse if faulty. Refer to Wiring Diagram.

-- If there is no voltage, repair or replace the wire. Refer to Wiring Diagram.

-- If the control head is faulty: replace the Driver Seat Adjustment Control Head Driver Seat Adjustment Control Head -E470- / Front Passenger Seat Adjustment Control Head Front Passenger Seat Adjustment Control Head -E471-. Refer to DRIVER/FRONT PASSENGER SEAT ADJUSTMENT CONTROL HEAD -E470- / -E471-, REMOVING AND INSTALLING .

-- If installed and the control module is faulty, replace the Memory Seat/Steering Column Adjustment Control Module Memory Seat/Steering Column Adjustment Control Module -J136- / Front Passenger Memory Seat Control Module Front Passenger Memory Seat Control Module -J521-. Refer to SEAT FUNCTIONS CONTROL MODULE, REMOVING AND INSTALLING .

-- If the seat forward/back adjustment motor is faulty, replace the seat pan. Refer to OVERVIEW - SEAT PAN .

Removing with faulty Driver and Front Passenger Seat Forward/Back Adjustment Motor Driver Seat Forward/Back Adjustment Motor -V28- /Front Passenger Seat Forward/Back Adjustment Motor -V31-

-- If necessary, remove the fire extinguisher mount. Refer to FIRE EXTINGUISHER BRACKET, REMOVING AND INSTALLING .

-- If necessary, remove the control module for the seat functions. Refer to SEAT FUNCTIONS CONTROL MODULE, REMOVING AND INSTALLING .

-- If necessary, remove the pneumatic system compressor. Refer to PNEUMATIC SYSTEM COMPRESSOR, REMOVING AND INSTALLING .

-- Unclip the cable holder -4- from the retainers.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of airbag deployment.

Risk of injury.

- Check if the airbag indicator lamp turns on or blinks.

- If the airbag indicator lamp turns on or blinks, the DTC memory must be read.

- If >>short circuit to positive<< is a DTC memory entry, disconnect the battery. Refer to BATTERY A, DISCONNECTING AND CONNECTING, VEHICLES WITHOUT ALTERNATIVE DRIVE SYSTEM, (0K0) / BATTERY A, DISCONNECTING AND CONNECTING, VEHICLES WITH HIGH-VOLTAGE SYSTEM, (0K3) / BATTERY A, DISCONNECTING AND CONNECTING, VEHICLES WITH ALTERNATIVE DRIVE SYSTEM, (0K4) .

- If there is a DTC memory entry, the Guided Fault Finding instructions on the Vehicle Diagnostic Tester must always be followed.

- If the airbag indicator lamp does not turn on or blink, or there is no DTC memory entry with >>short circuit to positive<< : switch off the ignition, keep the ignition key outside of the vehicle and wait 10 seconds.

CAUTION:

Pyrotechnical components can deploy unintentionally.

Risk of injury.

- Discharge the static electricity: quickly touch the door striker.

-- Disconnect the connectors on the connector station in the floor.

1 - For Versions with Rear Seat Entertainment

2 - Thorax airbag

3 - Seat Belt Latch/Seat Position Sensor

5 - Power Supply

6 - For Versions with Seat Heating

-- Remove the seat rail cover on the side sill side. Refer to SEAT RAIL COVER, REMOVING AND INSTALLING, SIDE SILL SIDE .

-- Unclip the rear bracket -2- for the wire routing on the seat pan with a flat-head screwdriver.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -1- on the seat forward/back adjustment motor.

-- Free up the wire -arrow-.

-- Remove the bolts -1 and 2- and remove the faulty seat forward/back adjustment motor -3- with the bracket.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the accessible bolts for the seat rails.

-- Push the front seat forward and back to remove the accessible bolts for the seat rails.

-- To protect the sill panel before prying out the front seat, attach the Universal Vehicle Protector :VAS 871001 .

Fig 2: Front Seat, Removing And Installing

Courtesy of AUDI OF AMERICA, LLC

-- Remove the front seat from the vehicle with a second technician.

-- Replace the seat pan. Refer to OVERVIEW - SEAT PAN .

-- Install the front seat. Refer to Installing .