Overview - Bumper Cover, A4 ALLROAD From Product Improvement

WARNING: This page is about a different car, the 2024 Audi A4 allroad. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Exploded View Of Rear Bumper Cover (A4 Allroad From Product Improvement)

Courtesy of AUDI OF AMERICA, LLC

Bumper Cover Upper Section
- Removing and Installing. Refer to BUMPER COVER UPPER SECTION, REMOVING AND INSTALLING .
- Bumper Cover, Removing and Installing. Refer to BUMPER COVER, REMOVING AND INSTALLING .
Trim Molding
- Removing and Installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, A4 LINES, A5 LINES AND A4 ALLROAD FROM PRODUCT IMPROVEMENT .
Small Reflector
- Removing and Installing. Refer to REFLECTOR, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Screw tightening specification: 2 Nm
Large Reflector
- Removing and Installing. Refer to REFLECTOR, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Screw tightening specification: 2 Nm
Mount
- For tail pipe trim
- Removing and Installing. Refer to FRAME FOR TAIL PIPE TRIM MOUNT, REMOVING AND INSTALLING, A4 FROM PRODUCT IMPROVEMENT .
Tail Pipe Trim
- Removing and Installing. Refer to TAIL PIPE TRIM, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
Bolt
- Quantity: 4
- 2 Nm
Bolt
- 2 Nm
Mount
- For the bumper cover
- Side
- Overview. Refer to OVERVIEW - BUMPER COVER MOUNT .
Bolt
- Quantity: 3
- Tightening specification Refer to OVERVIEW - BUMPER COVER MOUNT .
Mount
- For securing the bumper cover
- Overview. Refer to OVERVIEW - BUMPER COVER MOUNT .
Locking Mechanism
- For attaching the rear bumper cover to the upper mount
Bolt
- Tightening specification Refer to OVERVIEW - BUMPER COVER MOUNT .
Mount
- for lane change assistance control module
- Overview. Refer to OVERVIEW - LANE CHANGE ASSISTANCE .
Bolt
- Quantity: 3
- Tightening specification. Refer to OVERVIEW - LANE CHANGE ASSISTANCE .
Mount
- Left
- For the bumper cover
- Removing and Installing. Refer to CENTER BUMPER COVER MOUNT, REMOVING AND INSTALLING .
Bracket
- For Garage Door Opener Control Module -J530-
Nut
- Quantity: 2
- 3.5 Nm
Nut
- Quantity: 2
- 3.5 Nm
Mount
- Right
- For the bumper cover
- Removing and Installing. Refer to CENTER BUMPER COVER MOUNT, REMOVING AND INSTALLING .
Nut
- Quantity: 4
- 4 Nm
Sealing Washer
End Panel
- Removing and Installing. Refer to END PANEL, REMOVING AND INSTALLING .
Threaded Pin
- Quantity: 4
Bumper Cover Lower Section
- Removing and Installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING, A4 ALLROAD FROM PRODUCT IMPROVEMENT .
- Bumper Cover, Removing and Installing. Refer to BUMPER COVER, REMOVING AND INSTALLING .
Cover
- For the towing eye
Bolt
- Quantity: 4
- 2 Nm
Bumper Cover Lower Section
- Removing and Installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING, A4 ALLROAD FROM PRODUCT IMPROVEMENT .
Nut
- Quantity: 2
- 2 Nm
Impact Guard
- Removing and Installing. Refer to IMPACT GUARD, REMOVING AND INSTALLING .