Overview - Front Heater And A/C Unit Attachments, Air Distribution Housing, Heat EXCHANGER, Etc.

Fig 1: Exploded View Of Heater And A/C Unit Attachments, Air Distribution Housing, Heat Exchanger, Etc.

Courtesy of AUDI OF AMERICA, LLC

1. Insulation
   • Between the air duct in the air distribution housing and the one in the resonator chamber in the air intake housing.
   • RHD: arranged in a mirror image
2. Evaporator Housing
   • With the evaporator installed by the manufacturer
   • Depending on the version, further removal may not be necessary. Refer to OVERVIEW - EVAPORATOR HOUSING .
   • Removing and installing the evaporator. Refer to EVAPORATOR IN FRONT HEATER AND A/C UNIT, REMOVING AND INSTALLING .
   • RHD: arranged in a mirror image
3. Evaporator Vent Temperature Sensor -G263-
   • Removing and Installing. Refer to Evaporator Vent Temperature Sensor -G263-, REMOVING AND INSTALLING .
   • RHD: arranged in a mirror image
4. Plug
   • Plugs for example 8D0 819 598. Refer to the Parts Information.
   • Only present on a heater and A/C unit, on which cleaning of the evaporator has taken place.
5. Cap
   • For the connection to the glove compartment cooling
   • Not present on glove compartment cooling
6. Catch
   • Open carefully
7. Heater Core for the Heater
   • Removing and Installing. Refer to HEATER CORE, REMOVING AND INSTALLING .
   • Check the glued-on foam seals for damage and proper bonding. Refer to HEATER CORE, REMOVING AND INSTALLING .
8. Bolt
   • 1 Nm
9. Heat Exchanger Cover
   • For vehicles without Auxiliary Heater Heating Element -Z35-. Refer to the Parts Information.
   • There are different versions. Refer to the Parts Information.
   • Removing and Installing. Refer to HEATER CORE, REMOVING AND INSTALLING .
10. Heat Exchanger Cover
    • For vehicles with Auxiliary Heater Heating Element -Z35-. Refer to the Parts Information.
    • There are different versions. Refer to the Parts Information.
11. Auxiliary Heater Heating Element -Z35-
    • Not Installed
12. Zone Partition Grille
    • Only for vehicles without Auxiliary Heater Heating Element -Z35-. Refer to the Parts Information.
    • There are different versions. Refer to the Parts Information.
    • Removing and Installing. Refer to HEATER CORE, REMOVING AND INSTALLING .
13. Right Footwell Vent Temperature Sensor -G262-
    • Removing and Installing. Refer to Right Footwell Vent Temperature Sensor -G262-, REMOVING AND INSTALLING .
14. Heater and A/C Unit Air Distribution Housing with Evaporator
    • There are different versions. Refer to the Parts Information.
    • Heater and A/C Unit with Evaporator, Removing and Installing. Refer to HEATER AND A/C UNIT, REMOVING AND INSTALLING .
15. Left Footwell Vent Temperature Sensor -G261-
    • Removing and Installing. Refer to Left Footwell Vent Temperature Sensor -G261-, REMOVING AND INSTALLING .
16. Screw-Type Clamp
    • Replacing. Refer to the Parts Information.
    • Removing and installing on the heater core. Refer to HEATER CORE, REMOVING AND INSTALLING .
17. Bolt
    • 2 Nm
    • Removing and installing on the heater core. Refer to HEATER CORE, REMOVING AND INSTALLING .
18. O-Ring Seal
    • Replacing. Refer to the Parts Information.
    • Coat lightly with coolant before installing. Refer to HEATER CORE, REMOVING AND INSTALLING .
19. Coolant Pipe Spacer
    • Not installed
20. Coolant Pipe to Heater Core
    • Coolant return
    • Removing and installing on the heater core. Refer to HEATER CORE, REMOVING AND INSTALLING .
    • Can only be replaced when the heater and A/C unit is removed.
21. Coolant Pipe to Heater Core
    • Coolant supply
    • Removing and installing on the heater core. Refer to HEATER CORE, REMOVING AND INSTALLING .
    • Can only be replaced when the heater and A/C unit is removed.
22. Bracket for Coolant Pipes