Overview - Bumper Cover, A5 Basic/Lines From Product Improvement
WARNING: This page is about a different variant/trim than selected.
CAUTION:
There is a risk of explosions and fatal injuries due to damaged natural gas tanks.
- The natural gas tank must be checked for damage if components in the rear side or rear area are removed due to damage, such as the bumper cover, rear lid, underbody trim panels, longitudinal members, rear lid end piece, etc.
- Check for damage on fuel tanks. Refer to FUEL TANK .
- Small Reflector
- Removing and Installing. Refer to REFLECTOR, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Large Reflector
- Removing and Installing. Refer to REFLECTOR, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Bolt
- 2 Nm
- Mount
- Lower
- For the power rear lid opening sensors
- Bumper Cover
- Removing and Installing. Refer to BUMPER COVER, REMOVING AND INSTALLING .
- Bolt
- 2 Nm
- Mount
- For tail pipe trim
- Removing and Installing. Refer to FRAME FOR TAIL PIPE TRIM MOUNT, REMOVING AND INSTALLING, A5 FROM PRODUCT IMPROVEMENT .
- Bolt
- Quantity: 4
- 2 Nm
- Tail Pipe Trim
- Removing and Installing. Refer to TAIL PIPE TRIM, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Bolt
- Quantity: 4
- 2 Nm
- Mount
- For the bumper cover
- Side
- Overview. Refer to OVERVIEW - BUMPER COVER MOUNT .
- Bolt
- Quantity: 3
- Tightening specification Refer to OVERVIEW - BUMPER COVER MOUNT .
- Mount
- For securing the bumper cover
- Overview. Refer to OVERVIEW - BUMPER COVER MOUNT .
- Locking Mechanism
- For attaching the rear bumper cover to the upper mount
- Bolt
- Quantity: 2
- Tightening specification Refer to OVERVIEW - BUMPER COVER MOUNT .
- Mount
- Left
- For the bumper cover
- Removing and Installing. Refer to the appropriate Service Information .
- Nut
- Quantity: 2
- 3.5 Nm
- Nut
- Quantity: 2
- 3.5 Nm
- Mount
- Right
- For the bumper cover
- Removing and Installing. Refer to the appropriate Service information .
- Mount
- For tail pipe trim. Only on TDI engine
- Removing and Installing. Refer to FRAME FOR TAIL PIPE TRIM MOUNT, REMOVING AND INSTALLING, A5 FROM PRODUCT IMPROVEMENT .
- Nut
- Quantity: 2
- 3.5 Nm
- Tail Pipe Trim
- TDI engine: closed version
- Removing and Installing. Refer to TAIL PIPE TRIM, REMOVING AND INSTALLING, A4 AND A5 FROM PRODUCT IMPROVEMENT .
- Nut
- Only on TDI engine
- 3.5 Nm
- Nut
- Quantity: 4
- 4 Nm
- Cover
- For the towing eye
- Mount
- Upper
- For the power rear lid opening sensors
- Bumper Cover Lower Section
- "Basic" vehicle equipment version
- Removing and Installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING, A5 FROM PRODUCT IMPROVEMENT .
- Nut
- Quantity: 2
- 3.5 Nm
- Bumper Cover Lower Section
- "Lines" equipment version
- Removing and Installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING, A5 FROM PRODUCT IMPROVEMENT .
- Trim Molding
- "Lines" equipment version
- Removing and Installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, A4 LINES, A5 LINES AND A4 ALLROAD FROM PRODUCT IMPROVEMENT .