LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2023 >> A5 Quattro Prestige, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different car >> Section 337 (Engine Assembly (4-Cylinder Direct Injection 2.0L 4V TFSI Engine (Ea 888EVO4) (Coupe)) >> 10 Engine Assembly >> Assembly Mounts >> Overview - Assembly Mounts >> Overview - Engine Mount

Overview - Engine Mount

WARNING: This page is about a different car, the 2024 Audi S5, 2024 Audi RS 5, 2023 Audi S5, and 2023 Audi RS 5. However, it is still accessible from the selected car via links, so may be relevant.
Fig 1: Exploded View Of Engine Mount
GWWA10-11960Courtesy of AUDI OF AMERICA, LLC
  1. Subframe
  2. Assembly Mount Sensor
    • Equipped on some models
      • Assembly Mount Sensor 1 -G748-, left side
      • Assembly Mount Sensor 2 -G749-, right side
    • Removing and Installing. Refer to the appropriate Service Information .
    • Installation position. Refer to Fig 3.
  3. Bolt
    • For  Overview - Engine Mount
    • thread cutting
    • Position the bolt by hand and tighten it until it finds the old threads. Then tighten the bolt to the specification.
    • 11.5 Nm
  4. Bolt
    • 55 Nm
  5. Bolt
    • 20 Nm
  6. Bolt
    • 10 Nm
  7. Support Bearing
  8. Engine Support
  9. Bolt
    • 55 Nm
  10. Bolt
    • 10 Nm
  11. Heat Shield
  12. Engine Mount
    • with
      • Left Electrohydraulic Engine Mount Solenoid Valve -N144-
      • Right Electrohydraulic Engine Mount Solenoid Valve -N145-
    • Versions with
      • Assembly Mount Actuator 1 -N513-, right side
      • Assembly Mount Actuator 2 -N514- left
    • Removing and Installing. Refer to ENGINE MOUNT, REMOVING AND INSTALLING .
  13. Bolt
    • Replace after removing
    • 90 Nm + 90°
  14. Bolt
    • 30 Nm

      Support Bearing, Installation Position

      Fig 2: Support Bearing, Installation Position
      GWWA10-11984Courtesy of AUDI OF AMERICA, LLC
      • The raised section -2- of the engine support must engage into the opening -1- on the support bearing.

      Installation Position - Sensor with Assembly Mount Actuator

      Fig 3: Subframe Mount Sensor - Installation Position
      GWWA10-11435Courtesy of AUDI OF AMERICA, LLC
      • The sensor with the actuator -2- must engage in the hole -arrow- on the engine mount -1-.

      Assembly Mount Control ModuleJ931, Audi A6/A7

      Fig 4: Assembly Mount Control Module -J931-, Audi A6/A7
      GWWA10-12686Courtesy of AUDI OF AMERICA, LLC
      • Component location: in the left front wheel housing on the A-pillar.
      • Removing and Installing. Refer to the appropriate Service Information .

      -- Tighten the bolts -1- to 8 Nm.

      Assembly Mount Control ModuleJ931, Audi A8

      Fig 5: Assembly Mount Control Module -J931- Component Location
      GWWA10-12225Courtesy of AUDI OF AMERICA, LLC
      • Component location: in the left front wheel housing on the A-pillar.
      • Removing and Installing. Refer to the appropriate Service Information .

      -- Tighten the nuts -1 and 4- to 6 Nm.

      -- Tighten the bolts -arrows- to 6 Nm.

      GWWA10-12226Courtesy of AUDI OF AMERICA, LLC
scientia non olet · About LEMON Manuals