Camshaft Timing Chain, Removing From Camshafts, Cylinder Bank 2 (Left): Installing

• The crankshaft is locked using the Locking Pin: T10492  or Crankshaft Locking Pin: T40069  at "TDC" point.
• The Camshaft Positioning Tool : T40331/1  is tightened on the camshaft housing to 9 Nm.
• Replace the friction disk (diamond discs) after removal.

Courtesy of AUDI OF AMERICA, LLC

• The marks -1 and 2- on the camshaft adjusters must align with the corresponding locating tabs -arrows- on the camshaft housing.

-- Bring the camshaft adjuster with the camshaft timing chain positioned in the previously described installation position at the same time pay attention to the applied markings when removing.

Courtesy of AUDI OF AMERICA, LLC

-- Lubricate the control valves -1 and 2- on the threads and bolt head support and install all the way but do not tighten.

• Both camshaft adjusters must be able to be turned on the camshaft.

-- Remove the Locking Pins: T03006  .

• The help of a second technician is necessary for the following step.

  Courtesy of AUDI OF AMERICA, LLC

-- Have a second technician tension the Electronic Torque Wrench 3-60Nm : VAS6583  with insertion adapter Hazet 6423C or Stahlwille 7370/10 with Torque Wrench Insert - Ring Tool Attachment AF41 : VAS261001  and Counterholder: T90001  on the intake camshaft adjuster to 26 Nm counter-clockwise -arrow- and hold.

• Protection torque without using the insertion adapter Hazet 6423C/Stahlwille 7370/10 is 30 Nm.

-- Tighten the control valves with Socket E24: T90000  as follows while the camshaft adjuster is still being held under tension:

• Control valve -2- on the exhaust camshaft 30 Nm.
• Control valve -1- on the intake camshaft 30 Nm.

Valve Timing, Checking 

-- Remove the Camshaft Positioning Tool: T40331/1  .

-- Remove the Locking Pin: T10492  or Crankshaft Locking Pin: T40069  .

-- Using the Wrench - 21mm: T40263  and Adapter: T40314  , turn the crankshaft two turns -arrow- until the vibration damper is back at "TDC".

Courtesy of AUDI OF AMERICA, LLC

• The marks -1 and 2- on the camshaft adjusters must align with the corresponding locating tabs -arrows- on the camshaft housing.

  Courtesy of AUDI OF AMERICA, LLC

Procedures, where the engine is NOT removed: 

Courtesy of AUDI OF AMERICA, LLC

-- Insert the Locking Pin: T10492  on the groove -1- in the vibration damper all the way in the hole -arrow- in the belt pulley side sealing flange. If necessary push the crankshaft slightly back and forth.

Procedure, if the engine is removed due to preliminary work. 

Courtesy of AUDI OF AMERICA, LLC

-- Install the Crankshaft Locking Pin: T40069  in the hole and tighten to 20 Nm. If necessary push the crankshaft slightly back and forth.

Continuation: 

Courtesy of AUDI OF AMERICA, LLC

• The help of a second technician is necessary for the following step.

-- Have a second technician tension the Electronic Torque Wrench 3-60Nm: VAS6583  with insertion adapter Hazet 6423C with Torque Wrench Insert - Ring Tool Attachment AF41: VAS261001  and Counterholder: T90001  on the intake camshaft adjuster to 26 Nm counter-clockwise -arrow- and hold.

• Protection torque without using the insertion adapter Hazet 6423C/Stahlwille 7370/10 is 30 Nm.

• It must be easy to insert the Camshaft Lock: T40331/1  .

  Courtesy of AUDI OF AMERICA, LLC

• Do not use a hammer to install the camshaft positioning tool.

-- Insert the prepared Camshaft Positioning Tool : T40331/1  all the way in the camshaft.

• The Camshaft Positioning Tool: T40331/6  engages as shown in the flattened section -2- on the intake camshaft.
• The Camshaft Positioning Tool : T40331/7  engages as shown in the flattened section -1- on the exhaust camshaft.

If the Camshaft Positioning Tool: T40331/1  CANNOT be inserted:

-- Remove the Locking Pin: T10492  or Crankshaft Locking Pin: T40069  .

-- Insert the prepared Camshaft Positioning Tool: T40331/1  all the way in the camshafts as previously described. For this turn the crankshaft slightly.

-- Loosen the control valves -1 and 2- a half a turn using the Socket E24: T90000  .

Courtesy of AUDI OF AMERICA, LLC

Procedures, where the engine is NOT removed: 

Courtesy of AUDI OF AMERICA, LLC

-- Insert the Locking Pin: T10492  on the groove -1- in the vibration damper all the way in the hole -arrow- in the belt pulley side sealing flange. If necessary push the crankshaft slightly back and forth.

Procedure, if the engine is removed due to preliminary work. 

Courtesy of AUDI OF AMERICA, LLC

-- Install the Crankshaft Locking Pin: T40069  in the hole and tighten to 20 Nm. If necessary push the crankshaft slightly back and forth.

Continuation: 

-- Repeat the adjustment. Refer to Installing - Have a second technician tension the Electronic Torque Wrench 3-60Nm: VAS6583 with insertion adapter Hazet 6423C or Stahlwille 7370/10 with Torque Wrench Insert - Ring Tool Attachment AF41 : VAS261001 and Counterholder: T90001 on the intake camshaft adjuster to 26 Nm counter-clockwise -arrow- and hold. .

If the Camshaft Positioning Tool : T40331/1  can be inserted:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the Locking Pin: T10492  or Crankshaft Locking Pin: T40069  .

-- Remove the Camshaft Positioning Tool : T40331/1  .

-- Position the Counterholder: T90001  and Counterholder: T90002  on the intake camshaft adjuster.

-- Support the counterholder on the exhaust camshaft control valve -2-. If necessary slightly turn the crankshaft.

-- Turn the control valve -1- a 35° additional turn using the Socket E24: T90000  .

-- Position the Counterholder: T90001  and Counterholder: T90002  on the exhaust camshaft adjuster.

Courtesy of AUDI OF AMERICA, LLC

-- Support the counterholder on the intake camshaft control valve -1-. If necessary slightly turn the crankshaft.

-- Turn the control valve -2- an additional 35° turn using the Socket E24: T90000  .

-- Install the vacuum pump. Refer to VACUUM PUMP, REMOVING AND INSTALLING .

-- Install the cylinder bank 2 upper timing chain cover. Refer to UPPER TIMING CHAIN COVERS, REMOVING AND INSTALLING .

Additional procedures. Refer to CAMSHAFT TIMING CHAIN, REMOVING FROM CAMSHAFTS .