Cylinder Head Bank 2 (Left), Removing

Special tools and workshop equipment required 

• Engine Bung Set:VAS 6122 
  Fig 1: Engine Bung Set

  Courtesy of AUDI OF AMERICA, LLC
• Hose Clip Pliers:VAS 6340 
  Fig 2: Hose Clip Pliers VAS6340

  Courtesy of AUDI OF AMERICA, LLC
• Socket:T10405 
  Fig 3: Identifying Socket T30

  Courtesy of AUDI OF AMERICA, LLC

Procedure

-- Remove the left camshaft housing. Refer to CYLINDER BANK 2 (LEFT) CAMSHAFT HOUSING, REMOVING AND INSTALLING .

-- Remove the left turbocharger. Refer to TURBOCHARGER, REMOVING AND INSTALLING .

-- Remove the ribbed belt from the A/C compressor. Refer to A/C COMPRESSOR RIBBED BELT, REMOVING AND INSTALLING .

Audi RS6/RS7:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the A/C compressor. Refer to A/C COMPRESSOR, REMOVING AND INSTALLING .

-- Disconnect the connection -2- for Throttle Valve Control Module 2 -GX4-.

-- Remove the bolt -1- and free up the hose clamp.

Audi A8 / S8 / RSQ8 / SQ8 / SQ7:

-- Equipment version with refrigerant R134a/R1234yf without active suspension: remove the A/C compressor from the bracket and tie it up to the side. Refer to A/C COMPRESSOR, REMOVING AND INSTALLING ON BRACKET .

-- Versions with refrigerant R744 with active suspension: remove the A/C compressor. Refer to A/C COMPRESSOR, REMOVING AND INSTALLING .

-- Disconnect the connectors:

Courtesy of AUDI OF AMERICA, LLC

2 -  For the Charge Air Pressure Sensor 2 -G447-

3 -  For the Throttle Valve Control Module 2 -GX4-

-- Loosen the hose clamp -1- and remove the crankcase ventilation hose.

-- Remove the bolt -arrow- and free up the hose clamp.

Audi A8 / S8:

-- Loosen the hose clamp -4- and remove the air duct hose.

Audi RSQ8 / SQ8 / SQ7:

-- Remove the left lower air duct pipe on the throttle valve control module.

All:

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connectors:

2 -  For the Crankcase Ventilation Thermal Resistor 2 -N483-

3 -  For the Manifold Absolute Pressure Sensor 2 -G429-

5 -  For the Wastegate Bypass Regulator Valve 2 -N274-

-- Remove the charge air pressure actuator from the bracket and free it up and move it to the side.

-- Remove the crankcase ventilation pipe -1- to do so press the release buttons on both sides.

-- Disconnect the vacuum hose -4- by pressing the release buttons on both sides.

-- Free up the wires on the intake manifold.

-- Remove the bolt -1- and remove the coolant ventilation line -2- from the cylinder head.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -3- and the chain tensioner -4-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the guide rail bolt -5-.

-- If the cylinder head is removed with the engine installed: push the tensioning rail -2- upward -arrow- and secure using a cable tie to the camshaft timing chain -1- as shown.

-- Remove the bolts -arrows-.

-- Loosen the cylinder head bolts in the sequence -1 to 10-.

-- Remove the bolts and the cylinder head carefully.

-- Lay the cylinder head on a soft surface, such as foam.

-- Seal the open channels of the intake and exhaust tract with clean cloths or with thoroughly cleaned plugs from the Engine Bung Set:VAS 6122  .