Overview - Turbocharger
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2023 Audi SQ8, 2023 Audi RS Q8, 2022 Audi SQ8, 2022 Audi RS Q8, and 2021 Audi SQ8. However, it is still accessible from the selected car via links, so may be relevant.
- Exhaust Manifold
- Overview. Refer to OVERVIEW - EXHAUST MANIFOLD .
- Seal
- Replace after removing
- Screw-Type Clamp
- 25 Nm
- Turbocharger
- Shown for cylinder bank 1 (right)
- Removing and Installing. Refer to TURBOCHARGER, REMOVING AND INSTALLING .
- O-Ring
- Replace after removing
- Heat Shield
- Bolt
- Replace after removing
- 9 Nm
- Recirculation Valve
- Recirculation Valve, Bank 1 -N625-
- Recirculation Valve, Bank 2 -N626-
- Removing and installing. Refer to Turbocharger ; Recirculation Valve, Removing and Installing
- O-Ring
- For OVERVIEW - TURBOCHARGER
- Replace after removing
- Check Valve
- Installed depending on the version. Refer to the appropriate Electronic Parts Information.
- Installation position. Refer to Fig 3.
- Seal/O-Ring
- Included in a delivery package OVERVIEW - TURBOCHARGER, cannot be delivered separately
- Hose
- For the crankcase ventilation
- There are different versions. Refer to the appropriate Electronic Parts Information.
- Replace if damaged or leaking
- Replacing. Refer to CRANKCASE VENTILATION HOSE, REPLACING .
- Bolt
- All excluding engine codes DWKA/DWLA/DWNB/DWPA/DWRB: replace after removal
- 8 Nm
- Vacuum Diaphragm
- For the turbocharger
- Vacuum hose installation position. Refer to Fig 4.
- Replacing. Refer to TURBOCHARGER VACUUM DIAPHRAGM, REPLACING .
- Lock Nut
- 8 Nm
- Locking Spring
- Replace after removing
- Operating Lever
- For the vacuum diaphragm
- Nut
- 9 Nm
- O-Ring
- Replace after removing
- Bolt
- 9 Nm
- Upper Coolant Line
- Removing and Installing. Refer to UPPER COOLANT LINES ON TURBOCHARGER, REMOVING AND INSTALLING .
- Retaining Plate
- Bolt
- 9 Nm
- O-Rings
- Replace after removing
- Oil Supply Line
- Removing and Installing. Refer to OIL SUPPLY LINES ON TURBOCHARGER, REMOVING AND INSTALLING .
- O-Ring
- Replace after removing
- O-Ring
- Replace after removing
- O-Ring
- Replace after removing
- Lower Coolant Line
- Removing and Installing. Refer to LOWER COOLANT LINES ON TURBOCHARGER, REMOVING AND INSTALLING .
- Bolt
- 9 Nm
- O-Ring
- Replace after removing
- Bolt
- 9 Nm
- Oil Return Line
- Removing and Installing. Refer to OIL RETURN LINES ON TURBOCHARGER, REMOVING AND INSTALLING .
- Bolt
- 9 Nm
- O-Ring
- Replace after removing
- Bolt
- For OVERVIEW - TURBOCHARGER
- 9 Nm
- EVAP System Line
- Installed depending on the version. Refer to the appropriate Electronic Parts Information.
- O-Ring
- For OVERVIEW - TURBOCHARGER
- Replace after removing
Engine Cover Temperature SensorG765 - tightening specification
-- Tighten the bolt -1- to 9 Nm.
Check valve for crankcase ventilation - installation position
A - Points Outward
B - Points to the turbocharger
Vacuum hose for vacuum diaphragm - installation position
- The mark -1- on the vacuum hose must align with the markings -arrows- on the vacuum diaphragm.