Overview - Engine Compartment Lid

WARNING: This page is about a different car, the 2024 Audi SQ8, 2024 Audi Q8, 2023 Audi SQ8, and 2023 Audi Q8. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Exploded View Of Engine Compartment Lid

Courtesy of AUDI

Rear Lid
- Removing and Installing. Refer to REAR LID, REMOVING AND INSTALLING .
- Adjusting. Refer to REAR LID, ADJUSTING .
Nut
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Adapter
- For Release Button in Rear Lid Handle -E234-
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Release Button In Rear Lid Handle -E234-
- Component Location Overview. Refer to COMPONENT LOCATION OVERVIEW - CONTROLS IN LUGGAGE COMPARTMENT
Balance Weight
- Equipped on some models
Nut
- Quantity: 2
- 8 Nm
Rear Lid Control Head -EX58- with Rear Lid Lock Button in Luggage Compartment -E406-
- Removing and installing. Refer to REAR LID CONTROL HEAD -EX58-, REMOVING AND INSTALLING .
Plug
Mount
- Right
- With ball pin
Cover
- No replacement part
Latch
- Rear Lid Lock Unit -VX25-
- With Rear Lid Central Locking System Motor -V53-, Lock Pawl Contact Switch -F443-, equipped on some models: Rear Lid Contact Switch -F111-
- Removing and Installing. Refer to LATCH, REMOVING AND INSTALLING .
Nut
- Quantity: 2
- 21 Nm
Rear Lid Drive Unit 2 -VX77-
- Right
- With Rear Lid Motor 2 -V445- and Sensor in Rear Lid Motor 2 -G746-
- Removing and Installing. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, REMOVING AND INSTALLING .
- Programming. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, PROGRAMMING .
- Preparing for disposal. Refer to PREPARE THE Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77- FOR DISPOSAL. .
Mount
- Right
- With ball pin
Adjusting Buffer
- Right
- Removing and Installing. Refer to ADJUSTING BUFFER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT, ADJUSTING USING ADJUSTING BUFFER .
Rear Lid Seal
- Removing and Installing. Refer to REAR LID SEAL, REMOVING AND INSTALLING .
Striker
- Removing and Installing. Refer to STRIKER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT ADJUSTMENT AT STRIKER .
Bolt
- Quantity: 2
- 8 Nm
Nut
- Quantity: 2
- 21 Nm
Bolt
- Quantity: 2
- Replace after removing
- 10 Nm + 90°
Nut
- 20 Nm + 45°
Hinge
- Right
- Removing and Installing. Refer to HINGES, REMOVING AND INSTALLING .
Closing Assist Release Cable
- Removing and Installing. Refer to CLOSING ASSIST RELEASE CABLE, REMOVING AND INSTALLING .
Nut
- 20 Nm + 45°
Bolt
- Quantity: 2
- 12 Nm
Rear Lid Latch Trim Panel
- Removing and Installing. Refer to REAR LID LOWER TRIM PANEL, REMOVING AND INSTALLING .
Rear Lid Closing Assist Motor -V382-
- Removing and Installing. Refer to Rear Lid Closing Assist Motor -V382-, REMOVING AND INSTALLING .
Locking Element
- Quantity: 3
- For the closing assist
Power Rear Lid Opening Control Module -J938-
- Removing and Installing. Refer to Rear Lid Control Module -J605-, REMOVING AND INSTALLING .
Adjusting Buffer
- Left
- Removing and Installing. Refer to ADJUSTING BUFFER, REMOVING AND INSTALLING .
- Adjusting. Refer to HEIGHT, ADJUSTING USING ADJUSTING BUFFER .
Mount
- Left
- With ball pin
Rubber Grommet
- Removing and Installing. Refer to REAR LID, REMOVING AND INSTALLING .
Hinge
- Left
- Removing and Installing. Refer to HINGES, REMOVING AND INSTALLING .
Rear Lid Drive Unit -VX69-
- Left
- with Rear Lid Motor 1 -V444- and Sensor in Rear Lid Motor 1 -G745-
- Removing and Installing. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, REMOVING AND INSTALLING .
- Programming. Refer to Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77-, PROGRAMMING .
- Preparing for disposal. Refer to PREPARE THE Rear Lid Drive Unit -VX69- /Rear Lid Drive Unit 2 -VX77- FOR DISPOSAL. .
Bolt
- Quantity: 2
- Replace after removing
- 10 Nm + 90°
Cover
- No replacement part
Mount
- Right
- With ball pin