Component Location Overview - Heat Shield
WARNING: This page is about a different car, the 2024 Audi SQ8, 2024 Audi Q8, 2023 Audi SQ8, and 2023 Audi Q8. However, it is still accessible from the selected car via links, so may be relevant.
- Heat Shield
- For the front longitudinal member
- Removing and Installing. Refer to FRONT LONGITUDINAL MEMBER HEAT SHIELD, REMOVING AND INSTALLING .
- Tightening Specifications:
- Spring nuts: 2.5 Nm
- Nuts: 5 Nm
- Heat Shield
- For the plenum chamber bulkhead
- Removing and Installing. Refer to PLENUM CHAMBER BULKHEAD HEAT SHIELD, REMOVING AND INSTALLING .
- Heat Shield
- For left front longitudinal member
- Removing and Installing. Refer to FRONT LONGITUDINAL MEMBER HEAT SHIELD, REMOVING AND INSTALLING .
- Tightening Specifications:
- Spring nuts: 2.5 Nm
- Nuts: 5 Nm
- Heat Shield
- For the lower plenum chamber bulkhead
- Removing and Installing. Refer to LOWER PLENUM CHAMBER BULKHEAD HEAT SHIELD, REMOVING AND INSTALLING .
- Heat Shield
- For the rear longitudinal member
- Removing and Installing. Refer to REAR LONGITUDINAL MEMBER HEAT SHIELD, REMOVING AND INSTALLING .
- Left
- Tightening Specifications:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the front of the tunnel
- Left
- Removing and Installing. Refer to HEAT SHIELD FOR FRONT TUNNEL, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the transmission tunnel
- Removing and Installing. Refer to TRANSMISSION TUNNEL HEAT SHIELD, REMOVING AND INSTALLING .
- Heat Shield
- For the tunnel rear
- Left
- Removing and Installing. Refer to HEAT SHIELD FOR REAR TUNNEL, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the driveshaft
- Tightening specification:
- Spring nuts: 2.5 Nm
- Removing and Installing. Refer to DRIVESHAFT HEAT SHIELD, REMOVING AND INSTALLING .
- Heat Shield
- For the center of the exhaust system
- Removing and Installing. Refer to CENTER EXHAUST SYSTEM HEAT SHIELD, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the rear muffler
- Removing and Installing. Refer to REAR MUFFLER HEAT SHIELD, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the tunnel rear
- Right
- Removing and Installing. Refer to HEAT SHIELD FOR REAR TUNNEL, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the front of the tunnel
- Right
- Removing and Installing. Refer to HEAT SHIELD FOR FRONT TUNNEL, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For the top of the front tunnel
- Removing and Installing. Refer to UPPER FRONT TUNNEL HEAT SHIELD, REMOVING AND INSTALLING .
- Heat Shield
- For the rear longitudinal member
- Right
- Removing and Installing. Refer to REAR LONGITUDINAL MEMBER HEAT SHIELD, REMOVING AND INSTALLING .
- Tightening specification:
- Spring nuts: 2.5 Nm
- Heat Shield
- For left front tunnel brace
- Removing and Installing. Refer to HEAT SHIELD FOR FRONT TUNNEL BRACE, REMOVING AND INSTALLING .
- Heat Shield
- For right front tunnel brace
- Removing and Installing. Refer to HEAT SHIELD FOR FRONT TUNNEL BRACE, REMOVING AND INSTALLING .