FIBER-OPTIC CABLE, PREPARING WITH THE Fiber-Optic Conductor Repair Set :VAS6223A

WARNING: This page is about a different car, the 2024 Audi SQ7, 2024 Audi Q7, 2023 Audi SQ7, and 2023 Audi Q7. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Fiber-Optic Conductor Repair Set:VAS6223A

Fig 1: Identifying Fiber Optic Pliers Repair Set (VAS 6223A)
Courtesy of AUDI
Hose Cutting Pliers:VAS6228

Fig 2: Air Hose Pliers VAS 6228
Courtesy of AUDI
Vehicle Diagnostic Tester

CAUTION:

Do not bend the fiber-optic cable too much. The bending radius must be no less than 25 mm.

Fiber optic cables must not be routed over sharp edges.

The fiber-optic cable must not be dirty or touched with bare fingers.

Fiber optic cables may not be heated.

It is not permitted to twist together 2 fiber optic cables or one fiber optic cable with a copper wire.

Protect the connector and the connection box from dust. Place the cap on the trunk.

Mount Tool Head for the Fiber-Optic Repair Set - Pliers:VAS6223/1 .

Fig 3: Identifying Locking Pins

Courtesy of AUDI

-- Remove the locking pin in the direction of -arrows-.

Fig 4: Identifying Tool Set

Courtesy of AUDI

-- Remove the tool set in the direction of -arrow- and pull the locking pin back.

Fiber Optic Cable, Cutting to Length

Fig 5: Identifying Method To Cut Fiber Optic Cable To Length

Courtesy of AUDI

-- Establish length of fiber optic cable required.

-- Open the Fiber-Optic Repair Set - Pliers:VAS6223/1 and lay the fiber-optic cable -1- in the mount.

-- Close the Fiber-Optic Repair Set - Pliers:VAS6223/1 to cut the fiber-optic cable lengths.

Stripping

Fig 6: Identifying Open Position For VAS 6223/1

Courtesy of AUDI

-- Open the Fiber-Optic Repair Set - Pliers:VAS6223/1 .

-- Position the wire stripper in the lower position in the direction of -arrow-.

-- Insert fiber-optic cable into the stripping station.

The end of the fiber-optic cable must be flush with the rear side of the cutting pliers.

-- Close the Fiber-Optic Repair Set - Pliers:VAS6223/1 until the stop and keep closed.

Fig 7: Identifying Closed Position For VAS 6223/1

Courtesy of AUDI

-- Bend the wire stripper upward in the direction of -arrow- and remove the fiber-optic cable.

Precision Cutting (production of optical end face).

Fig 8: Identifying Position Of Fiber-Optic Cable In Cutting Position

Courtesy of AUDI

-- Push the fiber-optic cable -1- into the cutting station.

Insulation must make contact with cutting point stop.

-- Close the Fiber-Optic Repair Set - Pliers:VAS6223/1 and remove the wire.

Fig 9: Identifying Visual Inspection Of Cut Wire

Courtesy of AUDI

-- Visually inspect the wire -1- to make sure that it was cut correctly and that there are no burrs on the front surface.

NOTE:

Fiber-optic cable is only to be placed on an absolutely clean surface or held in hand.

Use the cap if there is a risk of the fiber-optic cable surface becoming dirty.

Attaching Brass Pin Contact to Fiber-Optic Cable.

Fig 10: Identifying Change Of Tool Head

Courtesy of AUDI

-- Change tool head in the direction of -arrow-.

Fig 11: Identifying Movement Of Fuse On VAS 6223/1 To Show "Stift"

Courtesy of AUDI

-- Slide the safeguard on the Fiber-Optic Repair Set - Pliers:VAS6223/1 in the direction of -arrow- so that the word "Stift" (pin) is legible.

-- Insert a brass pin contact -1- in the mount.

Fig 12: Identifying Inserted Brass Pin And Securing Lever

Courtesy of AUDI

-- Close the securing lever on the Fiber-Optic Repair Set - Pliers:VAS6223/1 in the direction of -arrow-.

-- Insert the fiber-optic cable into the brass pin contact -arrow- all the way up to the threaded stop and then close the Fiber-Optic Repair Set - Pliers:VAS6223/1 .

Fig 13: Identifying Inserted Fiber Optic Cable

Courtesy of AUDI

-- Open the fiber-optic cable pliers and remove the fiber-optic cable along with the brass contact pin.

CAUTION:

Do not excessively bend or kink the fiber-optic cables (minimum bending radius 25 mm).

-- Make sure the brass pin contact -2- is secured properly on the fiber-optic cable -1-.

Fig 14: Checking Proper Attachment Of Brass Pin Contact To Fiber Optic Cable

Courtesy of AUDI

4 crimped points must be visible on the brass connecting pin.
The brass pin contact must not be able to be removed by hand from fiber-optic cable.
The front surface of the fiber-optic cable is 0.01 to 0.1 mm behind the brass pin contact (visual check).

NOTE:

Connector couplings are available for connecting the fiber-optic cables. Refer to the appropriate Parts Information.

To install the new fiber optic cable in wiring harness connector. Refer to FIBER-OPTIC CABLE, DISCONNECTING FROM WIRING HARNESS CONNECTOR .

Corrugated Tube, Install On Fiber Optic Cable

Fig 15: Cutting Corrugated Tube To Appropriate Length Using Air Hose Pliers VAS 6228 Or A Sharp Knife

Courtesy of AUDI

-- Cut corrugated tube to appropriate length.

Use the Hose Cutting Pliers:VAS6228 or a sharp knife for cutting.
The corrugated tube must not be cut through using a side cutter under any circumstances
The corrugated tube must be cut on the wave peak -arrow-, not in the wave trough.
The corrugated tube must audibly engage in the fiber-optic cable housing when installing.

-- Guide the fiber-optic cable into the Fiber-Optic Repair Set - Tube Tool:VAS6223/10 as shown.

Fig 16: Guiding Fiber-Optic Cable Into Corrugated Tube With VAS 6223/10

Courtesy of AUDI

-- Position corrugated tube assembly pliers on slot on the tube.

-- Position crimping pliers for fiber-optic cable at slot of corrugated tube. The fiber optic cable is then routed in the corrugated tube.