Overview - Bumper Cover

Fig 1: Exploded View Of Rear Bumper Cover

Courtesy of AUDI OF AMERICA, LLC

1. Bumper Cover Mount
   • Center
   • Removing and installing. Refer to CENTER BUMPER COVER MOUNT, REMOVING AND INSTALLING .
2. Bumper Cover Mount
   • Nuts: 6 Nm
   • Lower
   • Removing and installing. Refer to BUMPER COVER MOUNT, REMOVING AND INSTALLING, BOTTOM .
3. Pop Rivet Nut
   • Quantity: 4
4. Bumper Cover
   • Removing and installing. Refer to BUMPER COVER, REMOVING AND INSTALLING .
5. Bumper Cover Lower Section
   • Equipment versions: S-line
   • Removing and installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING .
6. Bumper Cover Trim
   • Center
   • Removing and installing. Refer to BUMPER COVER TRIM, REMOVING AND INSTALLING, CENTER .
7. Cover
   • For the towing eye
8. Bumper Cover Trim Molding
   • Equipment versions: S-line
   • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, S LINE .
9. Spoiler
   • Removing and installing. Refer to SPOILER, REMOVING AND INSTALLING .
10. Spoiler
    • Lower
    • Removing and installing. Refer to SPOILER, REMOVING AND INSTALLING .
11. Rear Diffuser
    • Removing and installing. Refer to REAR DIFFUSER, REMOVING AND INSTALLING .
12. Bolt
    • 3 Nm
    • Quantity: 4
13. Power Rear Lid Opening Control Module -J938-
    • Removing and installing. Refer to Rear Lid Opener Control Module -J938-, REMOVING AND INSTALLING .
14. Bolt
    • 2.5 Nm
    • Quantity: 2
15. Bumper Cover Trim Molding
    • Side
    • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, STANDARD .
16. End Panel
    • For side bumper cover trim molding
    • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, STANDARD .
17. Bumper Cover Trim
    • Side. Refer to BUMPER COVER TRIM, REMOVING AND INSTALLING, SIDE .
    • Removing and installing. Refer to BUMPER COVER TRIM, REMOVING AND INSTALLING, CENTER .
18. Bolt
    • 2.5 Nm
    • Quantity: 2
19. Bolt
    • 2.5 Nm
    • Quantity: 2
20. Bumper Cover Trim Molding
    • Side
    • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, STANDARD .
21. End Panel
    • For side bumper cover trim molding
    • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, STANDARD .
22. Bumper Cover Trim Molding
    • Equipment versions: Standard
    • Removing and installing. Refer to BUMPER COVER TRIM MOLDING, REMOVING AND INSTALLING, STANDARD .
23. Bolt
    • 3 Nm
    • Quantity: 4
24. Spoiler
    • Removing and installing. Refer to SPOILER, REMOVING AND INSTALLING .
25. Bolt
    • 2.5 Nm
    • Quantity: 2
26. Cover
    • For the towing eye
27. Bumper Cover Lower Section
    • Equipment versions: Standard
    • Tightening sequence
    • Removing and installing. Refer to BUMPER COVER LOWER SECTION, REMOVING AND INSTALLING .
28. Bolt
    • 2.5 Nm
    • Quantity: 2
29. Bolt
    • 2.5 Nm
    • Quantity: 2
30. Bolt
    • 2.5 Nm
    • Quantity: 2
31. Bumper Cover Mount
    • Side
    • Removing and installing. Refer to BUMPER COVER MOUNT, REMOVING AND INSTALLING, SIDE .
32. Bolt
    • Tightening sequence. Refer to Fig 2.
    • Quantity: 6
33. Bumper Cover Mount
    • Upper
    • Removing and installing. Refer to BUMPER COVER MOUNT, REMOVING AND INSTALLING, TOP .
34. Bolt
    • Tightening sequence. Refer to Fig 3.
    • Quantity: 3
35. Nut
    • 4 Nm
    • Quantity: 5
36. Shield
    • For Lane Change Assistance Control Module -J769-, Lane Change Assistance Control Module 2 -J770-
    • Removing and installing. Refer to LANE CHANGE ASSISTANCE CONTROL MODULE -J769- / -J770-, REMOVING AND INSTALLING

Side Bumper Cover Mount - Tightening Specification and Sequence 

Fig 2: Side Bumper Cover Mount - Tightening Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bolts in sequence -1 through 6- to 3 Nm.

Upper Bumper Cover Mount - Tightening Specification and Sequence 

Fig 3: Upper Bumper Cover Mount - Tightening Sequence

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the bolts in sequence -1, 2 and 3- to 3 Nm.