Component Location Overview - Antenna Systems, From My 2021
WARNING: This page is about a different car, the 2022 Audi SQ7, 2022 Audi S7, and 2022 Audi Q7. However, it is still accessible from the selected car via links, so may be relevant.
- Emergency Call Module Antenna 3 -R323-
- Removing and Installing. Refer to EMERGENCY CALL MODULE ANTENNA, REMOVING AND INSTALLING, FROM MY 2021 .
- Close Range Communication Antenna -R269-
- Removing and Installing. Refer to CLOSE RANGE COMMUNICATION ANTENNA, REMOVING AND INSTALLING .
- Removing and Installing. Refer to EMERGENCY CALL MODULE ANTENNA, REMOVING AND INSTALLING, FROM MY 2021 .
- Wireless Data Transmission Antenna 2 -R366-
- Removing and Installing. Refer to Wireless Data Transfer Antenna 2 -R366-, REMOVING AND INSTALLING .
- Roof Antenna -R216-
- Bolt tightening specification: 5 Nm.
- Depending on vehicle equipment with the following integrated components:
- GPS Antenna -R50-
- Bluetooth Antenna -R152-, 9ZE/9ZV/9ZX
- Satellite Tuner Antenna -R172-, ER3 and QV3
- Auxiliary Heater Antenna -R182-, ER1/ER2 and 9M9
- Emergency Call Module Antenna 2 -R322-, IV1 through IV8/JE0 through JE4
- Roof Antenna Control Module -JX3-, FT1/FT2
- Removing and Installing. Refer to ROOF ANTENNA, REMOVING AND INSTALLING, FROM PRODUCT IMPROVEMENT .
- Antenna Amplifier 2 -R111-
- Screw tightening specification: 3 Nm
- Removing and Installing. Refer to Antenna Amplifier -R24- Antenna Amplifier 2 -R111- /TV Antenna Amplifier 1 -R82- /TV Antenna Amplifier 3 -R84-, REMOVING AND INSTALLING .
- TV Antenna Amplifier 3 -R84-
- Screw tightening specification: 3 Nm
- Removing and Installing. Refer to Antenna Amplifier -R24- Antenna Amplifier 2 -R111- /TV Antenna Amplifier 1 -R82- /TV Antenna Amplifier 3 -R84-, REMOVING AND INSTALLING .
- Antenna Amplifier -R24-
- Screw tightening specification: 3 Nm
- Removing and Installing. Refer to Antenna Amplifier -R24- Antenna Amplifier 2 -R111- /TV Antenna Amplifier 1 -R82- /TV Antenna Amplifier 3 -R84-, REMOVING AND INSTALLING .
- Antenna Amplifier 3 -R112-
- Screw tightening specification: 3 Nm
- Removing and Installing. Refer to Antenna Amplifier 3 -R112-, REMOVING AND INSTALLING .
- LTE Antenna 3 -R330-
- LTE antenna tightening specification to the bracket: 3.5 Nm
- Bracket tightening specification to the body: 3.5 Nm
- Removing and Installing. Refer to BUMPER ANTENNAS, REMOVING AND INSTALLING, FROM PRODUCT IMPROVEMENT .
- Emergency Call Module Antenna -R263-
- Antenna tightening specification to the bracket: 3.5 Nm
- Bracket tightening specification to the body: 3.5 Nm
- Removing and Installing. Refer to BUMPER ANTENNAS, REMOVING AND INSTALLING, FROM PRODUCT IMPROVEMENT .
- Windshield Antenna Suppression Filter -C18-
- Bolt tightening specification 4 Nm
- Nut tightening specification: 9 Nm
- Removing and Installing. Refer to WINDSHIELD ANTENNA SUPPRESSION FILTER, REMOVING AND INSTALLING .
- Close Range Communication Antenna 2 -R351-
- Removing and Installing. Refer to Close Range Communication Antenna 2 -R351-, REMOVING AND INSTALLING .
- Close Range Communication Control Module 2 -J1170-
- Removing and Installing. Refer to Near Field Communication Control Module 2 -J1170-, REMOVING AND INSTALLING .
- Close Range Communication Antenna -R350-
- Removing and Installing. Refer to Close Range Communication Antenna -R350-, REMOVING AND INSTALLING .