Overview - Oil Pan/Oil Pump, Version 1
WARNING: This page is about a different car, the 2022 Audi Q7. However, it is still accessible from the selected car via links, so may be relevant.
- Nut
- 9 Nm
- Oil Level Thermal Sensor -G266-
- Removing and Installing. Refer to Oil Level Thermal Sensor -G266-, REMOVING AND INSTALLING .
- Seal
- Replace
- Bolt
- Replace after removing
- Tightening Specifications and Sequence. Refer to Fig 2.
- Seal
- For oil pan lower plastic sections only
- Replace after removing
- O-Ring
- Replace after removing
- coat with engine oil
- Bolt
- Replace after removing
- 4 Nm +45°
- Suction Line
- Clean the screen if there are debris
- O-Ring
- Replace after removing
- coat with engine oil
- Oil Pump
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- Centering Bracket
- O-Ring
- Replace
- coat with engine oil
- Bolt
- Replace after removing
- Tightening specification -item : Bolt.
- Oil Pressure Regulation Valve -N428-
- Removing and Installing. Refer to Oil Pressure Regulation Valve -N428-, REMOVING AND INSTALLING .
- Chain Tensioner
- Oil Pump Drive Chain
- Mark the running direction before removal
- Bolt
- 9 Nm
- Cylinder Block
- Oil Screen
- Centering Bracket
- Oil Pan Upper Section
- Removing and Installing. Refer to OIL PAN UPPER SECTION, REMOVING AND INSTALLING .
- Bolt
- Replace after removing
- Tightening Specifications and Sequence. Refer to Fig 4.
- O-Ring
- Replace after removing
- coat with engine oil
- Bolt
- Replace after removing
- 4 Nm +45°
- Oil Return Pipe
- Bolt
- Replace after removing
- 8 Nm +90°
- Oil Baffle
- Replace after removing
- Bolt
- Replace after removing
- 4 Nm +45°
- Oil Pan Lower Section
- There are different versions. Refer to the Parts Information for the allocation.
- Removing and Installing. Refer to OIL PAN LOWER SECTION, REMOVING AND INSTALLING, VERSION 1 .
- O-Ring
- Seal for sheet metal oil pan lower sections
- O-ring for plastic oil pan lower sections
- Replace after removing
- Coat the O-ring with engine oil
- Oil Drain Plug or Plug
- Oil drain plug for sheet metal oil pan lower section
- Oil Drain Plug 30 Nm
- Plug for plastic oil pan lower section
- Tighten plug all the way
Oil Pan Lower Section made of Steel - Tightening Specification and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 19- | Install all the way by hand |
| 2. | -1 to 19- | 8 Nm |
| 3. | -1 to 19- | 90° additional turn |
Oil Pan Lower Section Made of Plastic - Tightening Specification and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 19- | Install all the way by hand |
| 2. | -1 to 19- | 8 Nm |
| 3. | -1 to 19- | 90° additional turn |
Oil Pan Upper Section - Tightening Specifications and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 14- | 8 Nm |
| 2. | -1 and 2- | 180° additional turn |
| 3. | -3 to 9- | 45° additional turn |
| 5. | -10 to 14- | 90° additional turn |