Overview - Oil Pan/Oil Pump, Version 2
WARNING: This page is about a different car, the 2022 Audi Q7. However, it is still accessible from the selected car via links, so may be relevant.
- Nut
- 9 Nm
- Oil Level Thermal Sensor -G266-
- Removing and Installing. Refer to Oil Level Thermal Sensor -G266-, REMOVING AND INSTALLING .
- Seal
- Replace after removing
- Bolt
- Replace after removing
- Tightening sequence. Refer to Fig 2.
- Oil Pan Lower Section
- Removing and Installing. Refer to OIL PAN LOWER SECTION, REMOVING AND INSTALLING, VERSION 2 .
- O-Ring
- Replace after removing
- coat with engine oil
- Plugs
- Tighten all the way
- Seal
- Replace after removing
- Bolt
- Replace after removing
- 4 Nm +45°
- Suction Line
- Clean the screen if there are debris
- O-Ring
- Replace after removing
- coat with engine oil
- Oil Pump
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- Centering Bracket
- Quantity: 2
- For the oil pump
- O-Ring
- Replace after removing
- coat with engine oil
- Bolt
- Replace after removing
- Tightening specification -item : Bolt.
- Oil Pressure Regulation Valve -N428-
- Check using the Vehicle Diagnostic Tester
- Removing and Installing. Refer to Oil Pressure Regulation Valve -N428-, REMOVING AND INSTALLING .
- Chain Tensioner
- Bolt
- 9 Nm
- Oil Pump Drive Chain
- Mark the running direction before removal
- Cylinder Block
- Bolt
- Replace after removing
- 4 Nm +45°
- Oil Baffle
- Oil Pan Upper Section
- Removing and Installing. Refer to OIL PAN UPPER SECTION, REMOVING AND INSTALLING .
- Bolt
- Replace after removing
- Tightening Specifications and Sequence. Refer to Fig 3.
- Plug
- Quantity: 3
- Oil Screen
- Bolt
- Replace after removing
- 8 Nm +90°
- O-Ring
- Replace after removing
- coat with engine oil
Oil Pan Lower Section - Tightening Specifications and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 to 17- | Install all the way by hand |
| 2. | -1 to 17- | 8 Nm |
| 3. | -1 to 17- | 90° additional turn |
Oil Pan Upper Section - Tightening Specifications and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
Depending on the version, aluminum or steel bolts may be installed.
A - Aluminum Bolts:
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 through 18- | 8 Nm |
| 2. | -1 through 13- | 45° additional turn |
| 3. | -14 through 18- | 90° additional turn |
B - Steel and Aluminum Bolts:
-- In this case, bolts 1 through 13 are steel bolts and bolts 14 through 18 are aluminum bolts.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening specification/additional turn |
|---|---|---|
| 1. | -1 through 13- | 15 Nm |
| 2. | -14 through 18- | 8 Nm |
| 3. | -1 through 18- | 90° additional turn |