Bevel Box, Removing: Procedure

WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2017 Audi S3, 2017 Audi A3 Quattro, 2016 Audi S3, 2016 Audi A3 Quattro, and 2016 Audi A3. However, it is still accessible from the selected car via links, so may be relevant.

-- Remove the noise insulation. Refer to NOISE INSULATION .

-- Remove the pendulum support. Refer to SUBFRAME MOUNT [For engine(s) CNSB, CNTC] .

-- Remove the fan shroud. Refer to RADIATOR/RADIATOR FAN For engine(s) CNSB, CNTC] .

-- Remove the nuts -arrows- and remove the right drives axle heat shield.

Courtesy of AUDI OF AMERICA, LLC

Vehicles with TDI Engine:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the EGR cooler. Refer to EGR COOLER, REMOVING AND INSTALLING .

All Vehicles:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- and remove the heat shield -1-.

-- Mark the position of the flexible disc and the bevel box flange to each other for re-installation.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the driveshaft from the bevel box -arrows- by counterholding at the triangular flange using a lever.

-- Push the engine/transmission assembly forward slightly (toward the front end) and remove the driveshaft from the bevel box.

Fig 1: Identifying Driveshaft Flange Shaft Seal

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

- Push the driveshaft horizontally toward the rear.

If the seal is damaged, the driveshaft must be replaced.

-- Remove the nut -1- for the right coupling rod -3- from the stabilizer bar -2-.

Courtesy of AUDI OF AMERICA, LLC

-- Using a felt-tip pen, mark the installation position of the right ball joint on the nuts -arrows-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the nuts.

-- Remove the right control arm from the ball joint.

During the assembly work, make sure that the ball joint rubber boot does not get damaged. If necessary, protect the ball joint rubber boot from damage.

-- Remove the right drive axle from the bevel box. Refer to DRIVE AXLE .

-- Tie up the driveshaft.

Make sure that the drive axle protective coating is not damaged.

-- Pivot the right suspension strut outward and support it with the :2024A/1 as shown.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

- Secure the pin and ball joint with the securing pin -arrow- and nut -1-.

-- Disconnect the connector -arrow- from the Oil Level Thermal Sensor -G266-.

Courtesy of AUDI OF AMERICA, LLC

There are different versions depending on the engine.

Vehicles with a TFSI Engine:

Fig 2: Tightening Sequence for Bevel Box Bracket (Vehicles with TFSI Engine)

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -1 and 2- and remove the bevel box bracket.

Vehicles with TDI Engine:

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -1-.

-- Remove the bolt -arrow- and push the Heater Support Pump -V488- to the right.

-- Remove the bolts -1 and 2- and remove the bevel box bracket.

Fig 3: Tightening Sequence for Bevel Box Bracket (0CN Transmission Support)

Courtesy of AUDI OF AMERICA, LLC

All Vehicles:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the right flange shaft bolt using the : T10107A by installing two bolts in the flange and counterholding the flange shaft with an assembly lever.

-- Remove the bolts -arrows- that connect the bevel box to the S tronic dual clutch transmission.

Courtesy of AUDI OF AMERICA, LLC

-- Fasten the :3300A to the subframe.

Courtesy of AUDI OF AMERICA, LLC

-- Place the spindle of the : 3300A on the transmission as shown.

-- Using the spindle on the : 3300A , only push the engine/transmission assembly so far forward until the bevel box can be removed.

Do not push the engine/transmission assembly too far forward, to not damage the fan shroud.

-- Carefully press the bevel box off of the S tronic dual clutch transmission while securing it from falling.

-- Remove the bevel box together with the right flange shaft.