Pinpoint Test BJ : The SEATBELT Warning Chime Or The Belt-Minder® Feature Is Inoperative
WARNING: This page is about a different car, the 2018 Lincoln Navigator. However, it is still accessible from the selected car via links, so may be relevant.
- BJ1 CHECK THE HEADLAMPS ON WARNING CHIME
- Ignition OFF.
- Turn the headlamps on.
- Open the driver door.
- Monitor the headlamps on warning chime.
Does the headlamps on warning chime operate?
Yes GO to BJ2 No Refer to IPC GUIDED ROUTINE TESTING -- NAVIGATOR . - BJ2 CHECK THE SEATBELT WARNING CHIME OPERATION
- Ignition ON.
- Monitor the seatbelt warning chime when the ignition switch is transitioned from OFF to RUN for 6 seconds.
Does the seatbelt warning chime operate for approximately 6 seconds?
Yes For the Belt-Minder®, GO to BJ3 For the seatbelt warning indicator, GO to BJ4 No GO to BJ4 - BJ3 CHECK THE SPEEDOMETER OPERATION
- Ignition ON.
- Verify the speedometer operates.
Does the speedometer operate?
Yes GO to BJ4 No GO to Pinpoint Test B - BJ4 PERFORM THE IPC (INSTRUMENT PANEL CLUSTER) SELF-TEST
- Using a diagnostic scan tool, perform the IPC self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to DTC Chart: Instrument Panel Cluster (IPC) . No GO to BJ5 - BJ5 PERFORM THE BCM (BODY CONTROL MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the BCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to: Body Control Module (BCM) . No GO to BJ6 - BJ6 PERFORM THE RCM (RESTRAINTS CONTROL MODULE) SELF-TEST
- Using a diagnostic scan tool, perform the RCM self-test.
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to:Airbag Supplemental Restraint System (SRS) . No GO to BJ7 - BJ7 CHECK THE GWM (GATEWAY MODULE A) DIAGNOSTIC TROUBLE CODES (DTCS)
- Using a diagnostic scan tool, check the GWM Continuous Memory Diagnostic Trouble Codes (CMDTCs).
Are any Diagnostic Trouble Codes (DTCs) recorded?
Yes REFER to: Communications Network . No GO to BJ8 - BJ8 CHECK THE DRIVER AND FRONT PASSENGER SEATBELT BUCKLE SWITCH
- Using a diagnostic scan tool, monitor the RCM driver and front passenger seatbelt buckle Parameter Identifications (PIDs) (SBELT_D_ST) and (SBLT_P_ST) while buckling and unbuckling the seatbelt.
Does the PID indicate current flowing with the seatbelt buckled and not flowing with the seatbelt unbuckled?
Yes GO to BJ9 No INSTALL a new seatbelt buckle. Refer to: Front Seatbelt Buckle . - BJ9 CHECK THE BELT-MINDER® CONFIGURATIONNOTE: Verify that an administrator key is used for this test and not a MyKey® programmed key. When a MyKey® programmed key is used, the Belt-Minder® is automatically turned on and cannot be disabled (if previously disabled by an administrator, the Belt-Minder® remains disabled when an administrator key is used).
- Verify the Belt-Minder® is activated or configured on for the seating position in question. Refer to: Seatbelt Minder Deactivating/Activating .
Is the Belt-Minder activated for the seating position in question?
Yes If the Belt-Minder® is always on above 10 km/h (6 mph) with the seatbelt unfastened, the system is operating correctly.If the Belt-Minder® is always on with the seatbelt fastened or never on with the seatbelt unfastened above 10 km/h (6 mph), INSTALL a new RCM. Refer to: Restraints Control Module (RCM) . No ACTIVATE the Belt-Minder® for the seating position in question. Refer to: Seatbelt Minder Deactivating/Activating .