LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2018 >> A6 Premium Plus >> Repair and Diagnosis >> External Pages >> Different car >> Section 370 (Sunroof - Roof Opening Panel) >> Diagnosis And Testing >> Roof Opening Panel >> Pinpoint Tests >> Pinpoint Test F : The Roof Opening Panel Does Not Open Or Close In Vent Position >> Pinpoint Test F : The Roof Opening Panel Does Not Open Or Close In Vent Position

Pinpoint Test F : The Roof Opening Panel Does Not Open Or Close In Vent Position

WARNING: This page is about a different car, the 2017 Lincoln Navigator and 2017 Ford Expedition. However, it is still accessible from the selected car via links, so may be relevant.
NOTE: Use the correct probe adapter(s) from the Flex Probe Kit when making measurements. Failure to use the correct probe adapter(s) may damage the connector.

  1. F1 CHECK THE MOTOR/MODULE FOR INITIALIZATION

    Was the roof opening panel initialization procedure successful? 

    Yes  The system is operating normally at this time. The roof opening panel motor was not initialized.
    No  GO to  F2.

  2. F2 CHECK THE ROOF OPENING PANEL SWITCH

    • Ignition OFF.
    • Disconnect: Roof Opening Panel Switch C930.
    • Carry out the roof opening panel switch component test. Refer to Component Testing for component testing.

    Is the roof opening panel switch OK? 

    Yes  GO to  F3.
    No  INSTALL a new roof opening panel switch. TEST the system for normal operation.

  3. F3 CHECK CIRCUIT CPR40 (YE/OG) FOR AN OPEN

    • Disconnect: Roof Opening Panel Motor/Module In-Line C922.
    • Measure the resistance between roof opening panel switch C930-8 , circuit CPR40 (YE/OG), and roof opening panel motor/module in-line C922-6 , circuit CPR40 (YE/OG), harness side.
    1. GFD137896Courtesy of FORD MOTOR COMPANY

    Is the resistance less than 5 ohms? 

    Yes  CHECK the roof opening panel motor/module jumper harness for loose pins or an open in circuit CPR40 (YE/OG) between roof opening panel motor/module in-line C922 , component side, and roof opening panel motor/module C921 , harness side. If the roof opening panel motor/module jumper harness is not OK, INSTALL a new roof opening panel motor/module jumper harness and TEST the system for normal operation. If the roof opening panel motor/module jumper harness is OK, GO to  F4.
    No  REPAIR the circuit. TEST the system for normal operation.

  4. F4 CHECK CIRCUIT CPR31 (VT/BN) FOR AN OPEN

    • Measure the resistance between overhead console C930-3 , circuit CPR31 (VT/BN), and roof opening panel motor/module in-line C922-7 , circuit CPR31 (VT/BN), harness side.
    1. GFD137897Courtesy of FORD MOTOR COMPANY

    Is the resistance less than 5 ohms? 

    Yes  CHECK the roof opening panel motor/module jumper harness for loose pins or an open in circuit CPR40 (YE/OG) between roof opening panel motor/module in-line C922 , component side, and roof opening panel motor/module C921 , harness side. If the roof opening panel motor/module jumper harness is not OK, INSTALL a new roof opening panel motor/module jumper harness and TEST the system for normal operation. If the roof opening panel motor/module jumper harness is OK, GO to  F5.
    No  REPAIR the circuit. TEST the system for normal operation.

  5. F5 CHECK THE ROOF OPENING PANEL MOTOR/MODULE FOR CORRECT OPERATION

    • Disconnect all roof opening panel motor/module connectors.
    • Check for:
      • corrosion.
      • bent pins.
      • pushed-out pins.
    • Connect all roof opening panel motor/module connectors and make sure they seat correctly.
    • Operate the system and verify the concern is still present.

    Is the concern still present? 

    Yes  INSTALL a new roof opening panel motor/module. REFER to Roof Opening Panel Motor . TEST the system for normal operation.
    No  The system is operating correctly at this time. Concern may have been caused by a loose or corroded connector. TEST the system for normal operation.
scientia non olet · About LEMON Manuals