LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2017 >> RS 3 >> Repair and Diagnosis >> External Pages >> Different car >> Section 36 (GENERIC SCAN TOOL [CNTA, CNTC, CNSB] (5 Of 5) -- (A3 SEDAN)) >> Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Charge Air Pressure Sensor - G31-, Checking >> Test Procedure

Test Procedure

WARNING: This page is about a different car, the 2018 Audi A3 Quattro, 2017 Audi A3 Quattro, 2016 Audi A3 Quattro, 2016 Audi A3, and 2015 Audi A3 Quattro. However, it is still accessible from the selected car via links, so may be relevant.
Step Procedure Result / Action to Take
1
  • PERFORM: Preliminary Check to verify the customers concern. Refer to PRELIMINARY CHECK .
-- Was Complaint verified?		 -- YES:
  • GO TO: Step 2.
-- NO:
  • GATHER more information from customer about the complaint.
2 
  • IGNITION: OFF.
  • DISCONNECT: Charge Air Pressure Sensor -G31- harness connector.
  • IGNITION: ON.
  • CHECK: Charge Air Pressure Sensor -G31- harness connector terminals 1 to 3 for voltage.
  • SPECIFIED VALUE: About 5.0 V. 
  • IGNITION: OFF.
-- Was Value obtained?		 -- YES:
  • GO TO: Step 3.
-- NO:
  • GO TO: Step 4.
3 
  • REMOVE: Engine Control Module - J623-. Refer to appropriate Service Information.
  • CHECK: Charge Air Pressure Sensor -G31- harness connector terminal 2 to the Engine Control Module - J623- harness connector T91 / 54 for resistance.
  • CHECK: Charge Air Pressure Sensor -G31- harness connector terminal 4 to the Engine Control Module - J623- harness connector T91 / 55 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). 
-- Were Values obtained?		 -- YES:
  • REPLACE: Charge Air Pressure Sensor -G31-. Refer to appropriate Service Information.
  • GO TO: Step 5.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 5.
4 
  • REMOVE: Engine Control Module - J623-. Refer to appropriate Service Information.
  • CHECK: Charge Air Pressure Sensor -G31- harness connector terminal 1 to the Engine Control Module - J623- harness connector T91 / 35 for resistance.
  • CHECK: Charge Air Pressure Sensor -G31- harness connector terminal 3 to the Engine Control Module - J623- harness connector T91 / 32 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). 
-- Were Values obtained?		 -- YES:
  • GO TO: Step 5.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 5.
5 
  • Final Procedure 
  • Perform a road test to verify repair.
-- Does the original DTC return?		 -- YES:
  • CHECK: Engine Control Module -J623- harness connector for any damaged, pushed-out pins.
  • REPAIR: As necessary.
  • If all electrical connections are OK:
  • REPLACE: Engine Control Module -J623-. Refer to appropriate Service Information.
  • Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  • Repair is complete. Generate Readiness Code. Refer to READINESS CODE .
  • Return vehicle to Customer.
-- NO:
  • Perform the diagnostic procedure for any DTC's.
  • If no DTC's return, the repair is complete.
  • Return vehicle to customer.
scientia non olet · About LEMON Manuals