LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2017 >> RS 3 >> Repair and Diagnosis >> External Pages >> Different car >> Section 36 (GENERIC SCAN TOOL [CNTA, CNTC, CNSB] (5 Of 5) -- (A3 SEDAN)) >> Generic Scan Tool >> Diagnosis And Testing >> Diagnostic Procedures >> Can-Bus Terminal Resistance, Powertrain, Checking >> Test Procedure

Test Procedure

WARNING: This page is about a different car, the 2018 Audi A3 Quattro, 2017 Audi A3 Quattro, 2016 Audi A3 Quattro, 2016 Audi A3, and 2015 Audi A3 Quattro. However, it is still accessible from the selected car via links, so may be relevant.
Step Procedure Result / Action to Take
1
  • PERFORM: Preliminary Check to verify the customers complaint. Refer to PRELIMINARY CHECK .
-- Was Complaint verified?		 -- YES:
  • GO TO: Step 2.
-- NO:
  • GATHER more information from customer about the complaint.
2 
  • IGNITION: OFF.
  • The Engine Control Module -J623- must remain connected for the following step. The central terminal resistor is located in the Engine Control Module -J623-.
  • REMOVE: Dual-Clutch Transmission Mechatronic -J743-. Refer to appropriate Service Information.
  • CHECK: Dual-Clutch Transmission Mechatronic -J743- harness connector terminals 15 to 10 for resistance.
  • SPECIFIED VALUE: 60 - 72 Ω (@ approx. 20° C). 
-- Was Value obtained?		 -- YES:
  • CONDITION: May be intermittent.
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 4.
-- NO:
  • GO TO: Step 3.
3 
  • REMOVE: Engine Control Module - J623-. Refer to appropriate Service Information.
  • CHECK: CAN bus circuit between the Dual-Clutch Transmission Mechatronic -J743- harness connector terminal 15 and the Engine Control Module -J623- harness connector T91 / 80 for resistance.
  • CHECK: CAN bus circuit between the Dual-Clutch Transmission Mechatronic -J743- harness connector terminal 10 and the Engine Control Module -J623- harness connector T91 / 79 for resistance.
  • SPECIFIED VALUE: 0.5 Ω (± 0.3 Ω). 
-- Were Values obtained?		 -- YES:
  • REPLACE: Engine Control Module -J623-. Refer to appropriate Service Information.
  • GO TO: Step 4.
-- NO:
  • PERFORM: Visual Inspection of wiring and component.
  • CHECK: Wiring for open, high resistance, short or harness connector for damage, corrosion, loose or broken terminals.
  • REPAIR: Faulty wiring or connector.
  • GO TO: Step 4.
4 
  • Final Procedure 
  • Perform a road test to verify repair.
-- Does the original DTC return?		 -- YES:
  • CHECK: Dual-Clutch Transmission Mechatronic -J743- harness connector for any damaged, pushed-out pins.
  • REPAIR: As necessary.
  • If all electrical connections are OK:
  • REPLACE: Dual-Clutch Transmission Mechatronic -J743-. Refer to appropriate Service Information.
  • Clear the DTC's. Refer to DIAGNOSTIC MODE 04 - ERASE DTC MEMORY .
  • Repair is complete. Generate Readiness Code. Refer to READINESS CODE .
  • Return vehicle to Customer.
-- NO:
  • Perform the diagnostic procedure for any DTC's.
  • If no DTC's return, the repair is complete.
  • Return vehicle to customer.
scientia non olet · About LEMON Manuals