Lower Timing Chain Cover, Removing And Installing: Installing

WARNING: This page is about a different car, the 2015 Audi S7, 2015 Audi RS 7, 2014 Audi S7, 2014 Audi RS 7, and 2013 Audi S7. However, it is still accessible from the selected car via links, so may be relevant.

Fig 1: Chamfer Alignment Bushing With File

Courtesy of AUDI OF AMERICA, LLC

Install in reverse order of removal. Note the following:

NOTE:

Replace any bolts that were tightened with an additional turn.

-- Remove the right upper alignment bushing from the cylinder block.

-- Grind the alignment bushing down at an angle as shown in the illustration.

Dimension -x- = 6.5 mm.
Dimension -y- = 8 mm.

-- Insert the alignment bushing in the cylinder block so the angled side faces up.

NOTE:

Because of the chamfer, the lower timing chain cover can be positioned more easily when the cylinder head is installed.

CAUTION:

Risk of contaminating the lubricating system.

Cover open parts of engine.

Fig 2: Cleaning Sealing Surfaces

Courtesy of AUDI OF AMERICA, LLC

WARNING:

Danger of eye injury.

Wear protective eyewear.

-- Remove any sealant residue still on the lower timing chain cover -1-, cylinder block and cylinder head with a rotating plastic brush.

-- Clean any oil or grease off the sealing surfaces.

-- Clean the threaded holes in the cylinder block for connecting the engine and transmission using a thread tap before installing the transmission.

-- Clean old sealant out of the holes -arrow- in the cylinder head seals.

Fig 3: Cleaning Old Sealant From Holes In Cylinder Head Gaskets

Courtesy of AUDI OF AMERICA, LLC

NOTE:

With cylinder head installed, holes in cylinder head seal are only half visible.

CAUTION:

The cylinder head seal could be damaged.

Only bend ends of cylinder head seals slightly, do not kink.

NOTE:

A kinked cylinder head seal must be replaced.

-- Bend the end of the cylinder head seals down slightly in direction of -arrows- until the upper sealing surface of the seals and the cylinder head can be cleaned.

-- Clean any oil and grease off the upper and lower cylinder head seals.

Fig 4: Bending Cylinder Head Gasket Ends Down

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Note the expiration date of the sealing compound.

Fig 5: Cutting Tube Nozzle At Front Marking (Nozzle Diameter Approx. 1 Mm)

Courtesy of AUDI OF AMERICA, LLC

-- Cut the tube nozzle at the front marking (nozzle diameter: about 2.5 mm).

-- Lightly the coat top and bottom cylinder head seal sealing surfaces with lubricant by bending the seals down slightly again in direction of -arrows-.

Fig 6: Bending Cylinder Head Gasket Ends Down

Courtesy of AUDI OF AMERICA, LLC

-- Use a flat object such as a feeler gauge to coat the surface between the cylinder head and seal.

-- Fill the cleaned cylinder head seal holes -arrow- with sealant.

Fig 7: Cleaning Old Sealant From Holes In Cylinder Head Gaskets

Courtesy of AUDI OF AMERICA, LLC

Fig 8: Identifying Cylinder Head Bolts Sealant Application Areas

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

The lubrication system could be plugged with excess sealant.

Do not apply sealant bead thicker than indicated.

-- Apply sealant beads -1 through 9- on the clean lower timing chain cover sealing surfaces as shown in the illustration.

Thickness of sealant beads: 2.0 mm.

NOTE:

The timing chains cover must be installed within 5 minutes after applying the sealant

-- Position the lower timing chain cover, guiding it diagonally from below to the sealing surface on the cylinder block and cylinder head.

-- When positioning, ensure the cylinder head seals are not damaged.

-- Tighten the bolts, refer to Figure.

Installation is performed in reverse order of removal, while noting the following:

-- Install the crankshaft seal on the transmission side, refer to CRANKSHAFT SEAL, REPLACING, TRANSMISSION SIDE .

-- Install the upper timing chain covers, refer to TIMING CHAIN COVER, REMOVING AND INSTALLING .

-- Install the Engine Coolant Circulation Pump 2 -V178-, refer to Engine Coolant Circulation Pump 2 -V178-, REMOVING AND INSTALLING .

-- Install the upper rear coolant pipe, refer to UPPER REAR COOLANT PIPE, REMOVING AND INSTALLING .

-- Install the drive plate, refer to DRIVE PLATE, REMOVING AND INSTALLING .