Overview - Oil Pan/Oil Pump
WARNING: This page does not describe the selected car, but rather 6 other vehicles, including the 2018 Audi S7, 2018 Audi RS 7, 2017 Audi S7, 2017 Audi RS 7, and 2016 Audi S7. However, it is still accessible from the selected car via links, so may be relevant.
NOTE:
If large quantities of metal particles or abraded material are detected during engine repairs, it may mean the crankshaft or connecting rod bearings are damaged. To prevent damage, perform the following steps after completing the repair; carefully clean the oil channels and replace the oil spray jets, the oil cooler and the oil filter.
Oil Pan Lower Section/Oil Pump
- Oil Level Thermal Sensor -G266-
- Removing and Installing. Refer to Oil Level Thermal Sensor -G266-, REMOVING AND INSTALLING .
- Seal
- Always replace
- Bolt
- Tightening specification and sequence. Refer to Fig 2
- Always replace
- Oil Pan Lower Section
- Removing and Installing. Refer to OIL PAN LOWER SECTION, REMOVING AND INSTALLING .
- Intake Tube
- For the oil pump
- Bolt
- 9 Nm
- O-Ring
- Always replace
- Bolt
- 8 Nm + 90°
- Always replace
- Oil Pipe
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- Bolt
- 8 Nm + 90°
- Always replace
- O-Ring
- Always replace
- Seal
- Always replace
- Alignment Sleeve
- Quantity: 2
- Input Shaft
- For the coolant pump
- Seal
- Always replace
- Oil Pump
- Do not disassemble
- With relief valve
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- Input Shaft
- For the oil pump
- Bolt
- 8 Nm + 90°
- Always replace
- Seal
- Always replace
- Oil Drain Plug
- 20 Nm
- Bolt
- 9 Nm
NOTE:
Replace the bolts that were tightened with an additional turn.
-- Tighten the bolts in stages as follows:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 19- | Install by hand all the way |
| 2. | -1 to 19- | 5 Nm |
| 3. | -1 to 19- | 90° additional turn |
Oil Pan Upper Section
- O-Ring
- Always replace
- For Audi RS6/RS7
- Thermostat
- For Audi RS6/RS7
- Comprised of a thermal element, spring and cover
- Circlip
- For the temperature regulator
- For Audi RS6/RS7
- Oil Pan Upper Section
- Removing and Installing. Refer to OIL PAN UPPER SECTION, REMOVING AND INSTALLING .
- Oil lines
- For Audi RS6/RS7
- Bolts
- 9 Nm
- For Audi RS6/RS7
- O-rings
- Always replace
- For Audi RS6/RS7
- O-Ring
- Always replace
- Seals
- Always replace
- O-Ring
- Always replace
- Front Engine Oil Cooler
- Removing and Installing. Refer to ENGINE OIL COOLER, REMOVING AND INSTALLING, FRONT .
- Change the coolant after replacing
- Bolt
- Tightening specification, refer to -item ) Bolt-.
- Bolt
- 8 Nm
- Cap
- Seal
- Always replace
- Bolt
- 9 Nm
- Guide Tube
- For the oil dipstick
- O-Ring
- Always replace
- O-Ring
- Always replace
- Alignment Pin
- Seal
- Always replace
- Alignment Pins
- Bolt
- Tightening specification and sequence. Refer to Fig 4.
NOTE:
Replace the bolts that were tightened with an additional turn.
-- Tighten the bolts in stages as follows:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 6- | Install by hand all the way |
| 2. | -1 to 6- | 5 Nm diagonally |
| 3. | -1 to 6- | In a diagonal sequence, turn an additional 90° |