Wheel Bearing In Control Position, Lifting Vehicles With Air Suspension

WARNING: This page does not describe the selected car, but rather 9 other vehicles, including the 2015 Audi S7, 2015 Audi RS 7, 2015 Audi A7 Quattro, 2014 Audi S7, and 2014 Audi RS 7. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Engine and Gearbox Jack VAS6931
Engine/Gearbox Jack Adapter - Wheel Hub Support T10149
Vehicle Diagnostic Tester

NOTE:

All chassis component bolts with bonded rubber bushings must be tightened with the control position.

Bonded rubber bushings have a limited range of motion.

Before axle components with bonded rubber bushings are tightened, they have to be brought to a position which matches the position when the vehicle is being operated (control position).

Otherwise the rubber mounting will be stressed, resulting in a reduced service life.

By raising appropriate suspension using Engine and Gearbox Jack VAS6931 and Engine/Gearbox Jack Adapter - Wheel Hub Support T10149, this position can be simulated on the hoist.

Front Axle

Engine must be installed.

Rear Axle

Before lifting the suspension, the vehicle must secured to the lifting arms on the hoist -arrow B- using the Tensioning Strap T10038 over the striker pin -arrow A-.

Fig 1: Identifying Tensioning Strap T10038

Courtesy of AUDI OF AMERICA, LLC

-- Place a piece of foam rubber -1- between the sill panel and the Tensioning Strap T10038 and then tension the Tensioning Strap T10038.

NOTE:

Be careful not to scratch the sill panel.

CAUTION:

The vehicle could fall off the hoist if it is not secured.

-- Place vehicle on hoist, refer to RAISING AND LOWERING WITH OPEN AND CLOSED AIR SUSPENSION SYSTEM .

-- Remove the air suspension system, refer to SYSTEM, VENTING OR FILLING .

-- Remove the wheel, refer to WHEELS AND TIRES .

-- Turn the wheel hub until one of the holes for the wheel bolts is on top.

Fig 2: Dimension Between Wheel Hub Center And Lower Edge Of Wheel Housing

Courtesy of AUDI OF AMERICA, LLC

-- Install Engine/Gearbox Jack Adapter - Wheel Hub Support T10149 with wheel bolt.

-- Insert Engine/Gearbox Jack Adapter - Wheel Hub Support T10149 into Engine and Gearbox Jack VAS6931 and press wheel bearing housing far enough upward until control position, dimension -a-, is obtained.

Dimension -a- is dependent on standing height of installed suspension:

Sportback Front Axle

Chassis ¹⁾	Dimension -a- in mm
Standard suspension (1BK)	386 mm ± 10 mm
Heavy duty suspension (1BS)	391 mm ± 10 mm
RS suspension (2MA)	386 mm ± 10 mm
Sport suspension (2MB)	386 mm ± 10 mm

Sedan/Avant Front Axle

Chassis ¹⁾	Dimension -a- in mm
Standard suspension (1BK)	384 mm ± 10 mm
Heavy duty suspension (1BS)	389 mm ± 10 mm
RS suspension (2MA)	384 mm ± 10 mm
Sport suspension (2MB)	384 mm ± 10 mm
allroad (1BY)	393 mm ± 10 mm

Sportback Rear Axle

Chassis ¹⁾	Dimension -a-
Standard suspension (1BK)	384 ± 10 mm
Heavy duty suspension (1BS)	389 ± 10 mm
RS suspension (2MA)	382 ± 10 mm
Sport suspension (2MB)	384 ± 10 mm

Sedan/Avant Rear Axle

Chassis ⁽¹⁾

Dimension -a-

Standard suspension (1BK)

382 ± 10 mm

Heavy duty suspension (1BS)

387 ± 10 mm

RS suspension (2MA)

384 ± 10 mm

Sport suspension (2MB)

382 ± 10 mm

allroad (1BY)

390 ± 10 mm

⁽¹⁾	The suspension that the vehicle is equipped with is indicated on the vehicle data plate. The suspension is indicated by a PR number. For the correct PR numbers and assigned suspensions, refer to PRODUCTION CONTROL NUMBER (PR NUMBER) EXPLANATION .

-- Lift the wheel bearing housing using the Engine and Gearbox Jack VAS6931 until the dimension -a- is reached.

Fig 3: Dimension Between Wheel Hub Center And Lower Edge Of Wheel Housing

Courtesy of AUDI OF AMERICA, LLC

WARNING:

Do not lift or lower the vehicle when the Engine and Gearbox Jack VAS6931 is below the vehicle.
Do not leave the Engine and Gearbox Jack VAS6931 under the vehicle any longer than necessary.

Working After Adjusting Control Position

-- Tighten the bolts and nuts.

-- Lower the wheel bearing housing.

-- Remove the Engine and Gearbox Jack VAS6931 from under the vehicle.

-- Remove Engine/Gearbox Jack Adapter - Wheel Hub Support T10149.

-- Install the wheel and tighten, refer to WHEELS AND TIRES .

-- Fill the air suspension system, refer to SYSTEM, VENTING OR FILLING .

WARNING:

All bolts and nuts must be tightened properly before driving the vehicle!