Bevel Box, Removing

Special tools and workshop equipment required 

• Engine Sling - Engine Bracket: 2024A/1 
• Engine Support Device: 3300A 
• Socket And Extended Bit: T10107A 

Procedure 

-- Remove the rear noise insulation. Refer to NOISE INSULATION, REMOVING AND INSTALLING .

-- Remove the pendulum support. Refer to PENDULUM SUPPORT, REMOVING AND INSTALLING 2.0L or PENDULUM SUPPORT, REMOVING AND INSTALLING 2.0L DIESEL .

Fig 1: Identifying Bolts

Courtesy of AUDI OF AMERICA, LLC

Vehicles with a TFSI Engine 

Fig 2: Identifying Right Drive Axle Heat Shield

Courtesy of AUDI OF AMERICA, LLC

-- Remove the nuts -arrows- and remove the right drive axle heat shield.

Vehicles with TDI Engine 

Fig 3: Identifying Air Guide Hose

Courtesy of AUDI OF AMERICA, LLC

-- Remove EGR cooler. Refer to EGR COOLER, REMOVING AND INSTALLING .

All Vehicles 

Fig 4: Identifying Heat Shield

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- and remove the heat shield -1-.

-- Remove the nut -1- for the coupling rod -3- from the right of the stabilizer bar -2-.

Courtesy of AUDI OF AMERICA, LLC

NOTE:

The illustration that follows shows the left front wheel suspension.

Fig 5: Ball Joint To Lower Control Arm Nuts

Courtesy of AUDI OF AMERICA, LLC

-- Mark the position of the nuts -arrows- for the right ball joint, and remove them.

-- Remove the right ball joint from the transverse link.

-- Remove right drive axle from bevel box. Refer to DRIVE AXLE, REMOVING AND INSTALLING .

-- Tie up the drives axle.

-- Move the right suspension strut to the outside and support it with the : 2024A/1  as illustrated.

Fig 6: Securing Pin And Control Arm Secured Using Securing Pin And Nut

Courtesy of AUDI OF AMERICA, LLC

-- Mark the position of the flexible disc and the bevel box flange shaft to each other for later use.

Fig 7: Driveshaft Flexible Disc

Courtesy of AUDI OF AMERICA, LLC

-- Using a lever to counterhold the triangular flange, remove the driveshaft from the bevel box -arrows-.

-- Press engine/transmission assembly forward slightly and remove driveshaft from bevel box.

Fig 8: Identifying Driveshaft Flange Shaft Seal

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -arrow- on the Oil Level Thermal Sensor -G266-.

Fig 9: Identifying Connector From Oil Level Thermal Sensor

Courtesy of AUDI OF AMERICA, LLC

Vehicles with a TFSI Engine 

Fig 10: Bevel Box Bracket (Vehicles with TFSI Engine)

Courtesy of AUDI OF AMERICA, LLC

-- Remove bolts -1 and 2- and the bevel box bracket.

Vehicles with TDI Engine 

Fig 11: Identifying Heater Support Pump Connector and Bolt

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -1-.

-- Remove the bolt -arrow-, and push the Heater Support Pump -V488- aside.

-- Remove bolts -1 and 2- and the bevel box bracket.

Fig 12: Bevel Box Transmission Support

Courtesy of AUDI OF AMERICA, LLC

All Vehicles 

Fig 13: Identifying Right Flange Shaft Countersunk Bolt, Socket And Key T10107

Courtesy of AUDI OF AMERICA, LLC

-- Remove right flange shaft bolt with : T10107  by installing two bolts in the flange and counter holding flange shaft with assembly lever.

-- Remove the bolts -arrows- that connect the bevel box to the S tronic transmission.

Fig 14: Identifying Bevel Box Bolts

Courtesy of AUDI OF AMERICA, LLC

-- Tighten the : 3300A  on the subframe.

Courtesy of AUDI OF AMERICA, LLC

-- Place the : 3300A  spindle on the transmission, as show in the illustration.

-- Only push the engine/transmission assembly with the : 3300A  spindles so far forward until the bevel box can be removed.

-- Carefully press bevel box off the S tronic transmission while protecting it against falling through.

-- Remove the bevel box together with the flange shaft.