Overview - Oil Pan/Oil Pump
WARNING: This page does not describe the selected car, but rather 8 other vehicles, including the 2017 Audi S3, 2017 Audi A3 Quattro, 2016 Audi S3, 2016 Audi A3 Quattro, and 2016 Audi A3. However, it is still accessible from the selected car via links, so may be relevant.
- Nut
- 9 Nm
- Oil Level Thermal Sensor -G266-
- Removing and Installing. Refer to Oil Level Thermal Sensor -G266-, REMOVING AND INSTALLING .
- Seal
- Replace after removing
- If the seal is not available separately, then the Oil Level Thermal Sensor -G266- must be replaced
- Oil Drain Plug or Plug
- Oil drain plug for sheet metal oil pan lower section
- Oil Drain Plug 30 Nm
- Plug for plastic oil pan lower section
- Turn the plug all the way using a flat-head screwdriver or a coin
- Gasket/O-Ring
- Replace after removing
- Allocation. Refer to the Parts Information.
- Seal/Liquid Sealant
- Replace the seal after removal.
- Allocation. Refer to the Parts Information.
- Bolt
- 4 Nm +45°
- Replace after removing
- Oil Baffle
- Replace after removing
- O-Rings
- Replace after removing
- Coat with engine oil
- Suction Line
- Clean the screen if there are debris
- Centering Bracket
- Quantity: 2
- For the oil pump
- Bolt
- Replace after removing
- Tightening sequence. Refer to Fig 4.
- Oil Pan Upper Section
- Removing and Installing. Refer to OIL PAN UPPER SECTION, REMOVING AND INSTALLING .
- Cylinder Block
- Oil Pump Drive Chain
- Mark the running direction before removal
- Bolt
- 9 Nm
- Chain Tensioner
- O-Ring
- Replace after removing
- Coat with engine oil
- Oil Pressure Regulation Valve -N428-
- Removing and Installing. Refer to Oil Pressure Regulation Valve -N428-, REMOVING AND INSTALLING .
- Bolt
- Replace after removing
- Tightening specification -item : Bolt.
- Oil Screen
- Oil Pump
- Removing and Installing. Refer to OIL PUMP, REMOVING AND INSTALLING .
- Bolt
- 8 Nm +90°
- Replace after removing
- O-Ring
- Replace after removing
- Coat with engine oil
- Bolt
- 4 Nm +45°
- Replace after removing
- Bolt
- Oil Pan Lower Section
- Removing and Installing. Refer to OIL PAN LOWER SECTION, REMOVING AND INSTALLING .
Oil Pan Lower Section Made of Plastic - Tightening Specification and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 20- | Install all the way by hand |
| 2. | -1 to 20- | 8 Nm |
| 3. | -1 to 20- | 90° additional turn |
Oil Pan Lower Section Made of Steel - Tightening Specification and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 to 20- | Install all the way by hand |
| 2. | -1 to 20- | 8 Nm |
| 3. | -1 to 20- | 45° additional turn |
Oil Pan Upper Section - Tightening Specifications and Sequence
- Replace bolts that were tightened with an additional turn after removing them.
- If when removing 14 bolts are installed then for the assembly 18 bolts must always be used.
Depending on the Version, Aluminum or Steel Bolts may be Installed.
A - Aluminum Bolts:
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 through 18- | 8 Nm |
| 2. | -1 and 2- | 180° additional turn |
| 3. | -3 to 13- | 45° additional turn |
| 4. | -14 through 18- | 90° additional turn |
B - Steel and Aluminum Bolts:
-- In this case, bolts 1 through 13 are steel bolts and bolts 14 through 18 are aluminum bolts.
-- Tighten the bolts in the steps in the sequence shown:
| Step | Bolts | Tightening Specification/Additional Turn |
|---|---|---|
| 1. | -1 through 13- | 15 Nm |
| 2. | -14 through 18- | 8 Nm |
| 3. | -1 through 18- | 90° additional turn |