Refrigerant Lines, Disconnecting From Quick-Release Couplings And Connecting: Installing

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.

Installation is done is reverse order, observe the following:

Fig 1: Installation Is Done Is Reverse Order, Observe Following

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Danger of leakage.

The couplings -B- and -C- on the refrigerant line -D- with inner heat exchanger must be replaced each time the refrigerant line is opened.

-- Pry the couplings -B- and -C- using a screwdriver -A- out of the refrigerant line -D- with inner heat exchanger -arrow-.

-- Thoroughly clean all parts of the refrigerant line connections (for example, using Cleaning SolutionD 009 401 04).

Fig 2: Identifying Parts Of Refrigerant Line Connections

Courtesy of AUDI OF AMERICA, LLC

-- Check the connector -A- for the refrigerant line with inner heat exchanger for damage.

-- Replace the O-rings -B and G-, the support rings -C and F- and the couplings -D and E-.

NOTE:

Follow the instructions for installing the O-rings. Refer to REFRIGERANT CIRCUIT SEALS .

-- Coat the O-ring seals with refrigerant oil prior to installation. Refer to REFRIGERANT CIRCUIT SEALS .

-- Press on the couplings -D- and -E- until this audibly latch into the refrigerant line with inner heat exchanger connector piece -A-.

-- Thoroughly clean the refrigerant lines -A- and -B- around the connection area and check for damage.

Fig 3: Identifying Refrigerant Lines -A- And -B-

Courtesy of AUDI OF AMERICA, LLC

-- Install the refrigerant lines -A- and -B- all the way so that they are free of tension.

Check for correct installation of the refrigerant lines.

Try to disconnect the refrigerant lines -A- and -B- ; the stop must be felt.
The pins -B- on the retaining ring must be visible on the quick-release coupling, version -A- (installed at SOP) when the locked refrigerant line -C- is pulled in direction of -arrow-.

Fig 4: Identifying Quick-Release Coupling Versions
Courtesy of AUDI OF AMERICA, LLC
On the quick-release coupling -D- (running change from MY 2010), the ring -E- must come out of the quick-release coupling -D-, when, after assembling, the locked refrigerant line -C- is pulled in direction of -arrow-. Then the ring -E- can be removed from the refrigerant line -C-.

NOTE:

Install the refrigerant lines such that they are not strained.

Check installation position of refrigerant lines to the quick-release couplings (they should not come in contact with other components).

-- Evacuate the refrigerant circuit and fill it. Refer to USING SERVICE STATION . For additional information, refer to OVERVIEW - REFRIGERANT CIRCUIT, NOT OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM and OVERVIEW - REFRIGERANT CIRCUIT, OPENING THE REFRIGERANT CIRCUIT, VEHICLES WITHOUT HIGH VOLTAGE SYSTEM (Refrigerant R134a, Servicing; Refrigerant Circuit, Using Service Station).

-- Turn on the ignition.

-- Install the remaining removed components.

-- Turn on the ignition.

-- Check the DTC memory for the Climatronic Control Module -- display and control head and erase any displayed malfunctions, if necessary using the Vehicle Diagnostic Tester in the "Guided Fault Finding " function.

-- Operate the A/C system after filling the refrigerant circuit. Refer to A/C SYSTEM, STARTING OPERATION AFTER FILLING REFRIGERANT CIRCUIT .

NOTE:

Observe the information regarding operating the A/C system after filling. Refer to A/C SYSTEM, OPERATING AFTER CHARGING , (Refrigerant R134a, Servicing; A/C System, General Information). After charging the A/C system before activating the A/C system.