LEMON Manuals: Even more car manuals for everyone
Home >> Audi >> 2016 >> S5 Prestige, 2D Convertible >> Repair and Diagnosis >> External Pages >> Different variant/trim >> Section 78 (Rear Suspension (1 Of 2) (Coupe)) >> 42 Rear Suspension >> Wheel Bearing And Trailing Arm >> Wheel Bearing Housing Bonded Rubber Bushing, Replacing >> Wheel Bearing Housing Rubber Bonded Bushing, Removing And Installing, All Wheel Drive (AWD) Vehicles >> Front Bonded Rubber Bushing, Installing

Front Bonded Rubber Bushing, Installing

WARNING: This page is about a different variant/trim than selected.
Fig 1: Front Rubber Bonded Bushing
GWWA42-10293Courtesy of AUDI OF AMERICA, LLC

-- Insert the bonded rubber bushing into the :T40184/3  . The "thin" collar -arrow- must face upward.

In Order To Install The Front Rubber Bonded Bushing, The :T40184/2  -3- Must Be Mounted On The Front Rubber Bonded Bushing In Such A Way So That The Lugs -2- Fit Into The Grooves -4-.

-- Press the front rubber bonded bushing all the way onto the thrust plates -1 and 6-.

Fig 2: Press Front Rubber Bonded Bushing All Way Onto Thrust Plates
GWWA42-10290Courtesy of AUDI OF AMERICA, LLC
  1. :VW401  . Arrange as illustrated.
  2. :T40184/3 
  3. Front bonded rubber bushing
  4. :VW408A 
  5. :T40184/2 
  6. :VW402  . Arrange as illustrated.

-- Then slightly pull apart the thrust plates -1 and 6-.

-- Press the front rubber bonded bushing approximately 2 mm out of the :T40184/3  .

Fig 3: Pressing Front Rubber Bonded Bushing Approximately 2 Mm Out Of T40184/3
GWWA42-10291Courtesy of AUDI OF AMERICA, LLC

a = 2 mm

-- Remove the :VW408A  and insert the :VW411  .

-- Position the wheel bearing housing on the :VAG1290A  .

-- Mount the front rubber bonded bushing (not shown in the illustration), the pressure plate -3- and the sleeve -1- on the wheel housing bearing.

Fig 4: Mount Front Rubber Bonded Bushing
GWWA42-10289Courtesy of AUDI OF AMERICA, LLC
  1. :T40184/3 
  2. :VW411 
  3. :T40184/2  . Pay attention to the installation position of the front rubber bonded bushing.

-- Place the tools on the front bonded rubber bushing and the wheel bearing housing -3- as illustrated.

Fig 5: Placing Tools On Front Bonded Rubber Bushing And Wheel Bearing Housing
GWWA42-10288Courtesy of AUDI OF AMERICA, LLC
NOTE:

When Mounting The Wheel Bearing Housing Onto The :T40184/1  Be Careful Not To Damage Or Push The Rubber Grommet On The Rear Rubber Bonded Bushing.

-- Slowly press the front rubber bonded bushing in (not shown in the illustration) until the sleeve -2- can be pulled out at the top.

  1. :VW411 
  2. :T40184/3 
  3. Wheel bearing housing
  4. :T40184/1  . The side with the groove must face the wheel bearing housing. On a bonded rubber bushing with a "positioning tab", this is in the groove on the :T40184/1  .
  5. :VW402 

Ignore item -3-.

Fig 6: Pressing Front Rubber Bonded Bushing Into Wheel Bearing Housing
GWWA42-10292Courtesy of AUDI OF AMERICA, LLC

-- Slowly press the front rubber bonded bushing -2- so that it is even with the edge -arrow- of the wheel bearing housing.

-- Install the wheel bearing housing. Refer To WHEEL BEARING HOUSING, REMOVING AND INSTALLING, FRONT WHEEL DRIVE (FWD) VEHICLES .

scientia non olet · About LEMON Manuals