Engine, Removing, 8-Speed Automatic Transmission 0BK

WARNING: This page is about a different car, the 2016 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Pry Lever :80-200
Step ladder, commercially available or Step Ladder :VAS5085
Engine Bung Set :VAS6122
Scissor Lift Table :VAS6131B with Scissor Lift Table - Audi Set :VAS6131/10 , Scissor Lift Table - A8 Set :VAS6131/11 and Scissor Lift Table - Q7 Set :VAS6131/13
Shop Crane - Drip Tray :VAS6208
Hose Clip Pliers :VAS6362
Hose Clip Pliers :VAS6340

NOTE:

With lock carrier installed, engine is removed downward with transmission and subframe.

During installation, cable ties must be installed at the same location.

WARNING:

When working on the whole exhaust system:

Follow the safety precautions when working on the exhaust system..

WARNING:

Risk of vehicle tipping over with engine removed.

Secure vehicle. Luggage compartment must be empty for this.

There is a risk of injury because the fuel is under very high pressure.

Reduce the fuel pressure down to residual pressure before opening high pressure area of the fuel injection system.

-- Position the front wheels so they are straight.

NOTE:

Release the electro-mechanical parking brake before disconnecting the battery so the driveshaft can be rotated to remove it.

CAUTION:

Danger of causing damage to electronic components.

Observe the steps for disconnecting the battery.

-- Turn off the ignition.

-- Disconnect the Ground (GND) cable from the battery terminal. Refer to BATTERY .

-- Remove the engine cover in direction of -arrows-.

Courtesy of AUDI OF AMERICA, LLC

-- Empty the coolant circuit. .

-- Remove the lock carrier cover. Refer to ATTACHMENTS, REMOVING AND INSTALLING .

Courtesy of AUDI OF AMERICA, LLC

WARNING:

Risk of scalding due to hot steam and hot coolant.

The coolant system is under pressure when the engine is warm.
Cover the coolant reservoir cap with a cloth and then open it slowly to release the pressure.

-- Remove the cap -arrow- from the coolant reservoir.

-- Remove the left and right front wheels. Refer to WHEELS AND TIRES .

-- Remove the left and right front wheel housing liners. Refer to WHEEL HOUSING LINER .

-- Remove the left and right front wheel spoiler. Refer to WHEEL HOUSING LINER .

-- Remove the noise insulations. Refer to NOISE INSULATION .

-- Remove the driveshaft. .

-- Place the :VAS6208 under engine.

-- Remove the drain plug -1- and drain the coolant.

Courtesy of AUDI OF AMERICA, LLC

-- Lift the clip -2- and disconnect the coolant hose from the radiator.

-- Loosen the clamp -arrow-, remove the coolant hose from the left lower coolant pipe and let the coolant drain out.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the right coolant hose from behind, lift the clamp -arrow-, and drain the coolant.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the plenum chamber cover. Refer to PLENUM CHAMBER COVER, REMOVING AND INSTALLING .

-- Remove the bolts -arrows- and air guide -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- and the air guide -2-.

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Ignore item -1-.

-- Open the clamps -arrows- and remove the air guide pipe -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect and free up the connector -2- from the Mass Airflow Sensor -G70-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the air filter housing -1- upward.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

There is a risk of contamination.

Follow the guidelines for cleanliness when working on the fuel supply system.

-- Loosen the clamps and remove the fuel hoses.

Blue fuel hose
Yellow fuel hose
White fuel hose

-- Open the clamp -2- and remove the coolant hose.

Courtesy of AUDI OF AMERICA, LLC

-- Loosen the clamp -1- and remove the vacuum connection from the plenum chamber bulkhead.

-- Loosen the clamp -arrow- and remove the coolant hose from the coolant pipe.

Courtesy of AUDI OF AMERICA, LLC

-- Loosen the clamp -3- and remove the air guide hose.

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Ignore items -1 and 2-.

-- Open the clamp -2- and remove the coolant line.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -1- and free up the refrigerant lines.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of damaging refrigerant lines and hoses.

Do not stretch, kink or bend refrigerant lines and hoses.

-- Remove bolt -2-, remove the refrigerant line from the Air Conditioning (A/C) compressor and set aside.

-- Seal the open lines and connections with clean plugs from the :VAS6122 .

NOTE:

Ignore items -1 and 3-.

-- Disconnect the connector -2- for Charge Air Pressure Sensor -G31- / Intake Air Temperature Sensor -G42- and free up the wire.

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Ignore item -1-.

-- Remove the tower brace. Refer to TOWER BRACE, REMOVING AND INSTALLING .

-- Release the retainer in direction of -arrow A- and open the cover in direction of -arrow B-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the nuts -2, 3 and 4- and free up the wire.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the connector -1- from the bracket and disconnect it.

-- Remove the bolts -arrows- and then remove Terminal 30 Wire Junction 2 -TV22- from the plenum chamber bulkhead.

-- Move the foam wedge -1- to the side.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows-.

-- Remove the nut -2- on the right longitudinal member and free up the GND wires.

-- Unlock the retainer in direction of -arrow-, open the wiring duct -1- and free up the wiring harness.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows-, pull the filler tube -1- out of the windshield washer fluid reservoir and out of the opening in the body and move it to the right.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the cap nut -2- and free up the GND cable.

-- Open the retainer in direction of -arrow- and remove the Engine Control Module -J623- -1- from the bracket and move it to the side.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- and the cover -1- from the plenum chamber E-box.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connectors -1- and remove the nut -2- for the wire.

Courtesy of AUDI OF AMERICA, LLC

-- Release the retainers -arrows- and remove the relay carrier with the fuse panel -3-.

-- Disengage the engine wiring harness from the plenum chamber E-box and free it up.

-- Release the retainers in direction of -arrows A- and remove the wiring bushing -1- upward in direction of -arrow B-.

Courtesy of AUDI OF AMERICA, LLC

-- Lay the wiring harness on the engine and secure the Engine Control Module -J623- so that it cannot fall.

-- Push the retainer back in direction of -arrow-, press the release down and disconnect the coolant fan connectors -1 and 2-, if applicable.

Courtesy of AUDI OF AMERICA, LLC

-- Free up the wiring harness.

-- Remove the air guide hose from the air guide pipe by loosening the hose clamp -arrow-.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -arrow- from the Right Front ABS Wheel Speed Sensor -G45- /Left Front ABS Wheel Speed Sensor -G47-.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the left and right connector -1- from the Left Front Level Control System Sensor -G78- /Right Front Level Control System Sensor -G289- and free up the wire -arrow-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the brake caliper and secure the brake caliper with the brake hoses still attached inside the wheel housing with wire. .

CAUTION:

Risk of damaging brake pistons.

Do not operate brake pedal when the brake caliper is removed.

-- Remove the nut -2- and the bolt -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the upper control arm upward from the wheel bearing housing in direction of -arrows-.

-- Repeat the procedure on the other side of the vehicle.

-- Remove the left and right stabilizer bar bolt -1-.

NOTE:

The bolts -2- will be removed later.

-- Remove the left and right nuts -3-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the subframe crossbrace. Refer to SUBFRAME CROSSBRACE, REMOVING AND INSTALLING .

CAUTION:

The suspension components could be damaged.

Do not rest the vehicle on its wheels if the subframe mount, the steering gear or the subframe crossbrace are not installed correctly.

-- Remove the left and right bolts -arrows- and the heat shield -1-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the steering intermediate shaft from the steering gear and the push the splines together. .

-- Release the safety catch in direction of -arrow-, push the retainer down and disconnect the connector from -2- from the Power Steering Control Module -J500-.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -1- from the Power Steering Control Module -J500-.

-- Free up the wiring harness.

-- Remove the ball socket -1- on the selector lever cable from the selector shaft lever using the :80-200 .

Courtesy of AUDI OF AMERICA, LLC

-- Press the securing clips -2- off and remove the selector lever cable from the transmission.

NOTE:

Do not bend or kink the selector lever cable.

If the engine and transmission are to be separated for the subsequent work, separate the drive plate threaded connection at the flywheel/torque converter. Refer to ENGINE AND TRANSMISSION, SEPARATING, VEHICLES WITH AUTOMATIC TRANSMISSION .

Prepare Scissor Lift Platform

Courtesy of AUDI OF AMERICA, LLC

-- Equip the :VAS6131B with the :VAS6131/10 and : VAS6131/11 , and :VAS6131/13 as follows:

Platform Coordinates	Components from the :VAS6131/10 , :VAS6131/11 and :VAS6131/13
B4	/13-4	/10-4	/10-5	/13-1
G4	/13-4	/10-4	/10-5	/13-1
B6	/10-1	/10-2	/10-5	/11-2
G6	/10-1	/10-2	/10-5	/11-2
A8 + C8	/13-6			/13-2
F8 + H8	/13-5			/13-2
B14	/10-1	/10-4	/10-5	/10-7
G14	/10-1	/10-4	/10-5	/11-1
F17 ¹⁾	/10-1	/10-4	/10-5	/13-2
¹⁾ For vehicles with a selective catalytic reduction system in this position no support elements are needed.

-- First manually secure the mounting elements to the scissor lift table.

-- Position the :VAS6131B horizontally.

Note bubble level (sight glass) on support platform.

-- Guide the :VAS6131B under the engine/transmission subassembly.

Courtesy of AUDI OF AMERICA, LLC

WARNING:

The subframe could cause an accident if it is not secured.

Do not loosen the subframe bolts -2 and 3-.

-- Remove the left and right subframe bolts -1-.

-- Attach mounting elements from the :VAS6131/10 and :VAS6131/13 at the left and right on the front of the subframe as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Ensure threaded spindles are completely installed.

-- Attach the mounting elements from the :VAS6131/10 and :VAS6131/11 to the front connecting points for the subframe crossbrace on the left and right sides at the rear as shown.

Courtesy of AUDI OF AMERICA, LLC

-- Position mounting elements from the :VAS6131/13 at the lower left and right on the wheel bearing housing as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Attach mounting elements from the :VAS6131/10 at the left and right rear of the crossmember as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Attach the mounting elements from the :VAS6131/10 and : VAS6131/13 under the front exhaust pipe, as shown in illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Rotate the mounting element spindles upward until all the mounting pins come into contact with the mounting points.

-- Attach mounting element base plates to :VAS6131B and tighten to 20 Nm.

-- Mark the location of the subframe and engine carrier to the longitudinal members using a felt-tip pen.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the left and right subframe bolts -2 and 3- in a diagonal sequence in stages.

-- Remove the bolts -arrows- on the tunnel crossmember.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the left and right bolts -2-.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of damaging hose and wiring connections as well as engine compartment.

Make sure all the hoses and lines between the engine, transmission, subframe and body have been disconnected.
Carefully guide the engine/transmission sub-assembly with subframe out of engine compartment while lowering.
Carefully guide the suspension struts past the longitudinal members.

-- Lower engine/transmission assembly.

-- Remove the Scissor Lift Table :VAS6131B with engine/transmission assembly from under the vehicle.