Engine And Transmission, Separating, Vehicles With S TRONICTRANSMISSION 0B5

WARNING: This page is about a different car, the 2016 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Scissor Lift Table - Audi Set :VAS6131/10

Courtesy of AUDI OF AMERICA, LLC
Articulated Joint Support :VAS6131/13-7 from the Scissor Lift Table - Q7 Set :VAS6131/13

Courtesy of AUDI OF AMERICA, LLC
Scissor Lift Table - Gearbox Support :VAS6131/14
Spindle :3367/3 from Press Tool For Viscous Fan :3367

Courtesy of AUDI OF AMERICA, LLC
Engine Support :T10014

Courtesy of AUDI OF AMERICA, LLC
Crankshaft Turning Tool :T40257

Courtesy of AUDI OF AMERICA, LLC
Wrench - 21mm :T40263

Courtesy of AUDI OF AMERICA, LLC
Adapter :T40314

Courtesy of AUDI OF AMERICA, LLC

Preparing the Articulated Joint Support :VAS6131/13-7 :

Courtesy of AUDI OF AMERICA, LLC

Spindle :3367/3 from Press Tool For Viscous Fan :3367
M10 nut
Engine Support :T10014
Articulated Joint Support :VAS6131/13-7

Courtesy of AUDI OF AMERICA, LLC

Engine/transmission assembly removed and placed on the Scissor Lift Table :VAS6131B .

Exhaust Gas Temperature Sensor Version 1

-- Remove the connectors -1, and 3- from the mount, disconnect, and free up the wires.

-- Disconnect the connector -2- and unclip the Differential Pressure Sensor -G505- from the bracket and free it up.

Exhaust Gas Temperature Sensor Version 2:

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connectors -1 and 4- and remove them from the bracket.

NOTE:

Ignore -items 2 and 3-.

Vehicles with an SCR system:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -1-.

NOTE:

Ignore -item 2-.

Continuation for All Vehicles:

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolt -3-.

NOTE:

Ignore -items 1 and 2-.

-- Remove nut -arrow-, and remove particulate filter with the front exhaust pipe.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the left and right driveshaft from the transmission flange shaft. Refer to DRIVE AXLE .

-- Loosen the clamp -arrow- and remove the coolant hose.

Courtesy of AUDI OF AMERICA, LLC

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

There is a risk of destroying the transmission control module (Mechatronic) with electrostatic discharge.

Always "discharge" the static electricity. Do this by touching a grounded object, for example vehicle ground, the vehicle or the hoist.
Do not touch contacts in transmission connector with hands.

-- Turn the twist lock counter-clockwise -arrow- and disconnect the connector from the transmission.

-- Free up the wiring harness on the transmission.

-- Remove bolts -arrows- and move the ATF cooler to the side.

Courtesy of AUDI OF AMERICA, LLC

NOTE:

Ignore -1, 2 and 3-.

-- Remove the lower cover -1- from the transmission -arrow-.

Courtesy of AUDI OF AMERICA, LLC

-- Join the tools as illustrated.

Courtesy of AUDI OF AMERICA, LLC

Socket 21 mm for ¹ /₂ "-drive

Courtesy of AUDI OF AMERICA, LLC

-- Counterhold the crankshaft to loosen the dual mass flywheel bolts.

NOTE:

When mounting, turn the crankshaft only in the direction of engine rotation -arrow-.

-- Remove the 6 bolts -arrow- from the dual mass flywheel. Turn the crankshaft an additional 60° in the direction of engine rotation.

Courtesy of AUDI OF AMERICA, LLC

-- Disconnect the connector -2-.

Courtesy of AUDI OF AMERICA, LLC

-- Remove bolt -3-, and move Transmission Fluid Cooling Valve -N509- to the side.

NOTE:

Ignore -item 1-.

-- Equip the Scissor Lift Table :VAS6131B with the Scissor Lift Table - Audi Set :VAS6131/10 and Scissor Lift Table - A8 Set : VAS6131/11 , and Articulated Joint Support :VAS6131/13-7 as follows:

Courtesy of AUDI OF AMERICA, LLC

NOTE:

The other attachments remain unchanged.

Table coordinates	Components from the Scissor Lift Table - Audi Set :VAS6131/10 , Scissor Lift Table - A8 Set :VAS6131/11 and Articulated Joint Support :VAS6131/13-7
F2	/13-7
B10	/10-1	/10-3	/10-5	/11-4
G10	/10-1	/10-3	/10-5	/11-4

-- Secure the Articulated Joint Support :VAS6131/13-7 to the engine on the front to the right with the M10 nut -arrow-, as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Install the joint support on the Scissor Lift Table : VAS6131B and tighten it to 20 Nm.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Danger of leaks in the ATF oil pan.

The Scissor Lift Table - Gearbox Support :VAS6131/14 must not be set on the ATF oil pan.

-- Attach the mounting elements from the Scissor Lift Table - Audi Set :VAS6131/10 and Scissor Lift Table - A8 Set : VAS6131/11 on the front of the transmission, as shown in illustration.

-- Turn the left and right spindles until the Scissor Lift Table - A8 Set - Mounting : VAS6131/11-4 are firmly touching the transmission.

-- Attach mounting element base plates to Scissor Lift Table :VAS6131B and tighten to 20 Nm.

-- Remove the starter bolts -1- and -2-.

Courtesy of AUDI OF AMERICA, LLC

-- Press the starter off the transmission and leave it in the installation position.

-- Remove the remaining bolts -3 through 10- that attach the engine to the transmission.

NOTE:

Ignore -item A-.

-- Loosen the side bolts -1- on the Scissor Lift Table :VAS6131B land the pull the rear table plate and transmission slightly toward the rear.

Courtesy of AUDI OF AMERICA, LLC