Prepare Scissor Lift Platform

WARNING: This page is about a different car, the 2018 Audi A6 Quattro, 2017 Audi A6 Quattro, and 2016 Audi A6 Quattro. However, it is still accessible from the selected car via links, so may be relevant.

Courtesy of AUDI OF AMERICA, LLC

-- Equip the :VAS6131B with the :VAS6131/10 and :VAS6131/11 , and :VAS6131/13 as follows:

Table Coordinates	Components from the :VAS6131/10 , :VAS6131/11 and :VAS6131/13
B4	/13-4	/10-4	/10-5	/13-1
G4	/13-4	/10-4	/10-5	/13-1
B6	/10-1	/10-2	/10-5	/10-11
G6	/10-1	/10-2	/10-5	/10-11
A8+C8	/13-6	-	-	/13-2
F8+H8	/13-5	-	-	/13-2
B14	/10-1	/10-3	/10-5	/11-1
G14	/10-1	/10-4	/10-5	/11-1

-- First manually secure the mounting elements to the scissor lift table.

-- Position the :VAS6131B horizontally.

Note bubble level (sight glass) on support platform.

-- Guide the :VAS6131B under the engine/transmission subassembly.

Courtesy of AUDI OF AMERICA, LLC

WARNING:

The subframe could cause an accident if it is not secured.

Do not loosen the subframe bolts -2 and 3-.

-- Remove the left and right subframe bolt -1-.

-- Attach mounting elements from the :VAS6131/10 and :VAS6131/13 at the left and right on the front of the subframe as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Ensure threaded spindles are completely installed.

-- Attach the mounting elements from the :VAS6131/10 at the left and right rear on the subframe crossbrace front connecting points as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Position mounting elements from the :VAS6131/13 at the lower left and right on the wheel bearing housing as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Attach mounting elements from the :VAS6131/10 and :VAS6131/11 at the left and right rear of the tunnel crossmember, as shown in the illustration.

Courtesy of AUDI OF AMERICA, LLC

-- Rotate the mounting element spindles upward until all the mounting pins come into contact with the mounting points.

-- Attach mounting element base plates to : VAS6131B and tighten to 20 Nm.

-- Mark the location of the subframe and tunnel crossmember to the longitudinal members using a felt-tip pen.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the left and right subframe bolts -2 and 3- in a diagonal sequence in stages.

-- Remove the bolts -arrows- on the tunnel crossmember.

Courtesy of AUDI OF AMERICA, LLC

-- Remove the left and right bolts -2-.

Courtesy of AUDI OF AMERICA, LLC

CAUTION:

Risk of damaging hose and wiring connections as well as engine compartment.

Make sure all the hoses and lines between the engine, transmission, subframe and body have been disconnected.
Carefully guide the engine/transmission sub-assembly with subframe out of engine compartment while lowering.

-- Next lower engine/transmission subassembly with :VAS6131B only by dimension -a-.

Courtesy of AUDI OF AMERICA, LLC

Dimension -a- = 100 mm maximum.

-- Remove the ball socket -2- on the selector lever cable from the selector shaft lever using the :80-200 .

Courtesy of AUDI OF AMERICA, LLC

-- Press the securing clips -1- off and remove the selector lever cable from the transmission.

NOTE:

Do not bend or kink the selector lever cable.

-- Remove the refrigerant line from the A/C compressor. Refer to A/C COMPRESSOR .

-- Lower the engine/transmission subassembly further.

-- Remove the :VAS6131B with engine/transmission assembly from under the vehicle.