Charge Air System, Checking For Leaks, Vehicles With The Engine Code CGQB

WARNING: This page is about a different car, the 2016 Audi Q5, 2015 Audi Q5, and 2014 Audi Q5. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Turbo System Tester Kit VAG1687 with Turbo System Tester Kit - Adapter 11 VAG1687/11 and Turbo System Tester Kit - Adapter 18 VAG168/18

Fig 1: Turbo System Tester Kit VAG1687
Courtesy of AUDI OF AMERICA, LLC

Procedure

Fig 2: Air Guide Pipe & Clamps

GWWA23-10600

Courtesy of AUDI OF AMERICA, LLC

-- Remove the engine cover, refer to ENGINE COVER, REMOVING AND INSTALLING .

-- Open the clamps -arrows- and remove the air guide pipe -1-.

-- Remove the crankcase ventilation hose -1- from the support -2- by pressing the release buttons.

Fig 3: Identifying Crankcase Ventilation Hose And Bolts

GWWA21-10696

Courtesy of AUDI OF AMERICA, LLC

-- Remove the bolts -arrows- and then remove the support from the turbocharger.

-- Connect the Turbo System Tester Kit - Adapter 18-1 VAG168/18-1 with the Turbo System Tester Kit - Adapter 18-2 VAG168/18-2 to the turbocharger.

Fig 4: Identifying Adapters VAG1687/18-1 And VAG1687/18-2

GWWA21-10697

Courtesy of AUDI OF AMERICA, LLC

-- Loosen the hose clamp -arrow- and remove the air guide hose.

Fig 5: Identifying Clamp And Air Guide Hose

GWWA21-10698

Courtesy of AUDI OF AMERICA, LLC

-- Connect the Turbo System Tester Kit - Adapter 11 VAG1687/11 on the air guide hose to the Throttle Valve Control Module -J338-.

Fig 6: Identifying Adapter VAG 1687/11

GWWA21-10651

Courtesy of AUDI OF AMERICA, LLC

-- Connect the hose -1- for the testing unit for turbo charger Turbo System Tester Kit VAG1687 to the adapter.

Prepare the Turbo System Tester Kit VAG1687 as follows:

Fig 7: Connecting Pressurized Air Hose To Testing Unit For Turbo Charger VAG 1687

GWWV21-0168

Courtesy of AUDI OF AMERICA, LLC

-- Fully turn out the pressure regulator valve -2- to the closed position and close the valves -3- and -4-.

The rotary knob must face upward so the pressure control valve -2- can be turned.

-- Connect the Turbo System Tester Kit VAG1687 to compressed air -1- with a commercially available adapter piece.

NOTE:

If there is water in the viewing glass, drain it through the drain plug -6-.

-- Open the valve -3-.

CAUTION:

Damage could result if the pressure is set too high.

Pressure must not exceed 0.5 bar!

-- Set the pressure to 0.5 bar using the pressure control valve -2-.

-- Open the valve -4- and wait until the test circuit is filled. Regulate the pressure to 0.5 bar again if necessary.

-- Listen, feel and use commercially available leak detection spray or the Ultrasonic Measuring Device VAG1842S to check the charge air system for leaks.

NOTE:

A small quantity of air dissipates via valves in engine. A pressure retention test is not possible for this reason.

For information on using the Ultrasonic Tester VAG1842S, refer to the instructions manual .

Release the pressure in the test circuit by pulling off the hose coupling before removing the adapter.

Assembling

Assemble in reverse order of disassembling. Note the following:

Tightening specification Figure.

NOTE:

Replace the seal and O-rings.