FIBER-OPTIC CABLE, PREPARING WITH THE Fiber-Optic Conductor Repair Set VAS6223A

WARNING: This page does not describe the selected car, but rather 13 other vehicles, including the 2017 Audi SQ5, 2017 Audi Q5, 2016 Audi SQ5, 2016 Audi Q5, and 2015 Audi SQ5. However, it is still accessible from the selected car via links, so may be relevant.

Special tools and workshop equipment required

Fiber-Optic Conductor Repair Set VAS6223A
Hose Cutting Pliers VAS6228
Vehicle Diagnostic Tester

CAUTION:

Do not bend the fiber-optic cable too much. The bending radius must be no less than 25 mm.

Fiber optic cables must not be routed over sharp edges.

The fiber-optic cable must not be dirty or touched with bare fingers.

Fiber optic cables may not be heated.

It is not permitted to twist together 2 fiber optic cables or one fiber optic cable with a copper wire.

Protect the connector and the connection box from dust. Place the cap on the trunk.

Mount Tool Head for the Fiber-Optic Repair Set - Pliers VAS6223/1.

Fig 1: Identifying Locking Pins

Courtesy of AUDI OF AMERICA, LLC

-- Remove the locking pin -arrows-.

Fig 2: Identifying Tool Set

Courtesy of AUDI OF AMERICA, LLC

-- Remove the tool set -arrow- and pull the locking pin back.

Fiber Optic Cable, Cutting to Length

Fig 3: Identifying Method To Cut Fiber Optic Cable To Length

Courtesy of AUDI OF AMERICA, LLC

-- Establish length of fiber optic cable required.

-- Open the Fiber-Optic Repair Set - Pliers and lay the fiber-optic cable -1- in the mount.

-- Close the Fiber-Optic Repair Set - Pliers to cut the fiber-optic cable lengths.

Stripping

Fig 4: Identifying Open Position For VAS6223/1

Courtesy of AUDI OF AMERICA, LLC

-- Open the Fiber-Optic Repair Set - Pliers VAS6223/1.

-- Position the wire stripper in the lower position -arrow-.

-- Insert fiber-optic cable into the stripping station.

The end of the fiber-optic cable must be flush with the rear side of the cutting pliers.

-- Close the Fiber-Optic Repair Set - Pliers until the stop and keep closed.

Fig 5: Identifying Closed Position For VAS6223/1

Courtesy of AUDI OF AMERICA, LLC

-- Bend the wire stripper upward -arrow- and remove the fiber-optic cable.

Precision Cutting (production of optical end face).

Fig 6: Identifying Position Of Fiber-Optic Cable In Cutting Position

Courtesy of AUDI OF AMERICA, LLC

-- Push the fiber-optic cable -1- into the cutting station.

Insulation must make contact with cutting point stop.

-- Close the Fiber-Optic Repair Set - Pliers VAS6223/1 and remove the wire.

Fig 7: Identifying Visual Inspection Of Cut Wire

Courtesy of AUDI OF AMERICA, LLC

-- Visually inspect the wire -1- to make sure that it was cut correctly and that there are no burrs on the front surface.

NOTE:

Fiber-optic cable is only to be placed on an absolutely clean surface or held in hand.

Use the cap if there is a risk of the fiber-optic cable surface becoming dirty.

Attaching Brass Pin Contact to Fiber-Optic Cable.

Fig 8: Identifying Change Of Tool Head

Courtesy of AUDI OF AMERICA, LLC

-- Change tool head -arrow-.

Fig 9: Identifying Movement Of Fuse On VAS6223/1 To Show "Stift"

Courtesy of AUDI OF AMERICA, LLC

-- Slide the safeguard on the Fiber-Optic Repair Set - Pliers -arrow- so that the word "Stift" (pin) is legible.

-- Insert a brass pin contact -1- in the mount.

Fig 10: Identifying Inserted Brass Pin And Securing Lever

Courtesy of AUDI OF AMERICA, LLC

-- Close the securing lever on the Fiber-Optic Repair Set - Pliers -arrow-.

-- Insert the fiber-optic cable into the brass pin contact -arrow- all the way up to the threaded stop and then close the Fiber-Optic Repair Set - Pliers.

Fig 11: Identifying Inserted Fiber Optic Cable

Courtesy of AUDI OF AMERICA, LLC

-- Open the fiber-optic cable pliers and remove the fiber-optic cable along with the brass contact pin.

CAUTION:

Do not excessively bend or kink the fiber-optic cables (minimum bending radius 25 mm).

-- Make sure the brass pin contact -2- is secured properly on the fiber-optic cable -1-.

Fig 12: Checking Proper Attachment Of Brass Pin Contact To Fiber Optic Cable

Courtesy of AUDI OF AMERICA, LLC

4 crimped points must be visible on the brass connecting pin.
The brass pin contact must not be able to be removed by hand from fiber-optic cable.
The front surface of the fiber-optic cable is 0.01 to 0.1 mm behind the brass pin contact (visual check).

NOTE:

Connector couplings are available for connecting the fiber-optic cables.

To install the new fiber optic cable in wiring harness connector. Refer to FIBER-OPTIC CABLE, DISCONNECTING FROM WIRING HARNESS CONNECTOR .

Corrugated Tube, Install On Fiber Optic Cable

Fig 13: Cutting Corrugated Tube To Appropriate Length Using Air Hose Pliers VAS6228 Or A Sharp Knife

Courtesy of AUDI OF AMERICA, LLC

-- Cut corrugated tube to appropriate length.

Use the Hose Cutting Pliers VAS6228 or a sharp knife for cutting.
The corrugated tube must not be cut through using a side cutter under any circumstances
The corrugated tube must be cut on the wave peak -arrow-, not in the wave trough.
The corrugated tube must audibly engage in the fiber-optic cable housing when installing.

-- Guide the fiber-optic cable into the Fiber-Optic Repair Set - Tube Tool VAS6223/10 as shown.

Fig 14: Guiding Fiber-Optic Cable Into Corrugated Tube With VAS6223/10

Courtesy of AUDI OF AMERICA, LLC

-- Position corrugated tube assembly pliers on slot on the tube.

-- Position crimping pliers for fiber-optic cable at slot of corrugated tube. The fiber optic cable is then routed in the corrugated tube.